Q2) Three forces act on the piping. Determine the sum of the moments of the three forces about point P. 0.2 m 4 kN 0.2 m 2 kN 20° 2 kN 40.2 m 0.2 m

Q: Determine the horizontal and vertical components of force at pins B and C. The suspended cylinder…

A: Draw FBD of CB: Resolving horizontal and vertical forces:

Q: What is the Maximum moment in kN-m. Given: w = 48, a = 5, b = 4, and c = 1. w kN/m B. a m b m cm RA…

A:

Q: Problem #2 A 6m Y kN/m C A B The support at A can be assumed to be a roller. Point C is an internal…

A:

Q: F 45 N m 500 N

A:

Q: Determine the horizontal and vertical components of force at pins B and C. The suspended cylinder…

A: Given data : Mass = 75 kg Determine the horizontal and vertical component of force at pin B and C?

Q: The hoist supports the 150-kg engine. Determine the force in members DB and FB. Also determine the…

A:

Q: 1. What is the reaction at A? (kN) 2. What is the reaction at B? (kN) 3. What is the shear 12 m from…

A:

Q: solve for each force

A: P= 4.5kN To find force in all members of the truss

Q: 1. Forces P and F acting along the bars maintain equilibrium of pin A. Determine the values of P and…

A:

Q: Hinge A Plate 1.2 m. F 1.2 m x 1.2 m) B 30 Container liquid

A: To find force on gate AB

Q: Determine the value of reaction at support E if the applied 1 unit load is on point D. Hinge. E…

A: Energy reaction power is applied to a structure when it depends on something. The analysis of the…

Q: Determine the resultant moment produced by the forces about point Oof the cases below. 500 N F, =…

A:

Q: What is the Maximum moment in kN-m. Given: w1 = 42, w2 = 11, a = %3D 3, b = 4, and c = 3. w1 kN/m w2…

A:

Q: A 45° P

A:

Q: The smooth pipe rests against the opening at the points of contact A, B, and C. Determine the…

A: The given figure is shown below:

Q: Q2/ The cable of the tower crane is subjected to 840 N force. A fixed base at A supports the crane.…

A:

Q: Solve the frame approximately using Portal Method. 30KN 6m k 60KN- 6m 72KN- 8m 10 m 12m 10 m 1.…

A:

Q: The 30-N uniform rod has a length of l = 1 m. If s = 1.5 m, determine the distance h of placement at…

A: The free body diagram of the wall and cable is given below.

Q: 4 kN -9 m

A:

Q: Analyze the beam below: 1 m Α.Δ. 400 kN/m 6 m 2 m 600 kN B 2 m (a) determine the maximum moment…

A:

Q: 4

A:

Q: For the below structure a moment is applied at E, find the equilibrium moments exerted by the…

A:

Q: w1 kN/m w2 kN/m D B. am bm cm

A:

Q: Determine the magnitude of the pin force at B. A 0.4 m 0.6 m 200 N·m B 0.4 m 0.4 m

A:

Q: Calculate the reaction force at support F. a=4m; b=3m; c=2m; d=2m; P=7kN. A a d ● B 60° D b F OC YP

A:

Q: Determine the components horizontal and vertical reaction exerted by the pins A and B on the frame…

A: Solution:

Q: 5) Obtain the support reactions for the system given below. A and B are pin supports C is a hinge.…

A:

Q: Determine the reactions of the beam using Force Method Analysis. Set A is fixed, B is roller and w =…

A: Given- a cantilever beam fixed at end A and provided with  roller support at B end.  Required- Using…

Q: Determine the magnitude of the pin force at B. 0 0.43 m 0.61 m 125 N-m B 0.43 m 0.43 m

A: To find out the magnitude of the pin force at  B.

Q: The frame below is made up of three 2 m long rods. The pin at D resides in a slot with a friction…

A: Given : Length of rods = 2m  Friction coefficient = 0.35  Determine if the frame slips when a 10 N…

Q: What is the location of the Maximum moment from A in meters. Given: w1 = 44, %3D w2 = 12, a = 3, b =…

A: Given a simply supported beam with udl as shown below w1 = 44 w2 = 12 a=3 b=2 c=3 The location of…

Q: For designing horizontal curves based on sight distance, the radius of the curve is designed to be…

A: For the safety of drivers, it is essential to consider proper sight distance when constructing…

Q: 4. The engine hoist is used to support the 160-kg engine. Determine the force acting in the…

A: To Determine The force acting in the hydraulic cylinder AB, the horizontal and vertical components…

Q: Determine the reactions on the beam given the loadings below using VIRTUAL WORK METHOD. Use the…

A:

Q: 100 Kg A C D - 3.00 m -イ 5.00 m 4.00 m 300 Kg

A:

Q: Calculate the following: a) Support reactions at A and D b) Find the force in BC c) Calculate the…

A:

Q: 100 kN 10 kN/m A 12 m 6 m 21

A:

Q: 4. The engine hoist is used to support the 160-kg engine. Determine the force acting in the…

A:

Q: Determine the reaction at support B using Force method analysis. Assume support A is fixed and…

A:

Q: Y kN 30° 30° Am A -1.5 m- Bm X kN 9. What is the moment reaction of the support at A? (kN-m) 10.…

A: Given:- X=137, Y=37, A=6, B=8, and C=1 To find:- Moment at A Vertical reaction at A Horizontal…

Q: The spool of wire having a weight of 300 lb rests on the ground at B and against the wall at A.…

A: Given:-  weight of Spool of wire = 300lb  Coefficient of friction= 0.35

Q: 5. Determine the maximum positive moment created at pt. B in the beam shown due to the wheel loads…

A: GIven- Loads=4Kn,8Kn,3Kn The diagram is given below-

Q: Problem no. 1. Compute the reaction forces at pt. A and B D C A 9m B 3m 1.5 m 3 m 30° 20 KN

A:

Equilibrium and Support Reactions

Civil engineers deal with structures that are composed of several members connected or with individual members such as beams and columns. To analyze such structures, the condition of statics must be applied. Under the static condition, the members are considered to be in equilibrium under the action of forces, that is, the members are assumed to be having negligible velocity.