Q2 Oil with a density of 850 kg/m³ and kinematic viscosity of 0.00062 m²/s is being discharged by a 6-mm diameter, 45-m-long horizontal pipe from a storage tank open to the atmosphere. The height of the liquid level above the center of the pipe is 3 m. Disregarding the minor losses, determine the flow rate of oil through the pipe.

Q2 Oil with a density of 850 kg/m³ and kinematic viscosity of 0.00062 m²/s is being discharged by a 6-mm diameter, 45-m-long horizontal pipe from a storage tank open to the atmosphere. The height of the liquid level above the center of the pipe is 3 m. Disregarding the minor losses, determine the flow rate of oil through the pipe.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Glycerin flows at 35 m through a 150 mm diameter new wrought iron pipe at a velocity of 3 m/s. It has an absoluteviscosity of 1.50 Pa-s and a specific gravity of glycerin = 1.26.1. Determine the Reynold’s number.
One end of a tube of unknown radius is immersed to a depth of 15 mm in water and an air bubble is blown at the end of this tube. The maximum air pressure measured is 200 Pa. The same procedure is carried out in a liquid and the maximum air pressure recorded in 150 Pa. Determine the surface tension of the liquid. Data given: Density of water = 997 kg/m3 Density of liquid = 850 kg/m3 Density of air = 1.2 kg/m3 Surface tension of water = 72 mN/m
A capillary tube viscometer is being selected to measure viscosity of a liquid food. The maximum viscosity to be measured will be 230 cP and the maximum flow rate that can be measured accurately is 0.015 kg/min. If the tube length is 10cm and a maximum pressure of 25 Pa can be measured, determine the tube diameter to be used. The density of the product is 1000 kg/m3.
A capillary tube viscometer is being selected to measure viscosity of a liquid food. The maximum viscosity to be measured will be 230 cP and the maximum flow rate that can be measured accurately is 0.015 kg/min. If the tube length is 10cm and a maximum pressure of 25 Pa can be measured, determine the tube diameter to be used. The density of the product is 1000 kg/m3.
Thermo-Fluid
M5
Air (ρa = 0.08 lbm/ft3) flows through a furnace where it is burned with fuel toproduce a hot gas (ρg = 0.05 lbm/ft3) that flows up the stack, as shown in the following figure.The pressures in the gas and the immediately surrounding air at the top of the stack at point Aare equal. What is the difference Δh (in.) in water levels in the manometer connectedbetween the base B of the stack and the outside air at point C? Which side rises? Except forthe pressure drop across the furnace (which you need not worry about), treat the problem asone in hydrostatics. That is, ignore any frictional effects and kinetic energy changes in thestack. Also, you can neglect compressibility effects and assume that the density of gas isconstant.
(a) Prove that the loss of pressure head for the viscous flow through a circular pipe is given by h.
Question 2A large vat contains water, which contains a drainage pipe at a height h1, as shown infigure 2. The drainage pipe has a length L. = 0.4 m, and a radius R = 15 mm, and releaseswater to the atmosphere at a flow rate Q. The connection between the pipe and the vatwall has a loss coefficient of KL = 0.8.Point A is in the middle of the tank at a height, hi.You can assume that the flow in the drainage pipe is fully developed and laminar. The density of water is p = 1000 kg/m° and the viscosity is u = 1 mPa.s. The acceleration due to gravity is 9.81 m/s? a) Find an expression for the pressure at point A.b) Find an expression in terms of Q, L, d, K, p and u for the pressure losses along the pipe (including the losses at the inlet and exit).c) If the flowrate out of the drainage tank is Q = 50 L/min, find ho. You may assumeany change of ho with time is negligible.
Water at 15 degrees Celsius is flowing through a 2-in ID smooth pipe. The friction loss for a 100-ft section of the pipe amounts to 4.8 lbf/lbm. Determine the velocity of the flow.
Water at 35 degrees Celsius is flowing through a smooth pipe with a length of 80m and a diameter of 250mm. The Reynolds number for the flow is 75000. Assuming the pipe is completely horizontal and the flow is isothermal, determine the friction head developed in the flow. By how much is the inlet pressure reduced because of the friction?
At a speed of 0.2 m/s, light oil with a density of 880kg/m and a viscosity of 2.1cP is pumped from a huge oil tanker to a power plant's storage tank. The discharge point is 50m above the liquid level in the tanker, at the top of the storage tank. The pipeline is a 150mm smooth pipe with six typical 90° elbows and two gate valves that is 200 meters long (fully open). The atmosphere is vented from both the oil tanker and the storage tank. a. Calculate the pressure drop in J/kg along the pipeline. b. Calculate the pumping power (in kW) if the pump-motor set has a 65 percent efficiency.