Q2: Non rotating beam shown in the (fig.2), (F=100 lb), find the maximum stress and its location. Take R= 0.5 in F lb - 3 in.- -3 in. - -2 in.- -2 in. -1 in.- 1 in. dia. 1층 in. dia. 1 in. dia. Fig. 2 Ib /2

Q2: Non rotating beam shown in the (fig.2), (F=100 lb), find the maximum stress and its location. Take R= 0.5 in F lb - 3 in.- -3 in. - -2 in.- -2 in. -1 in.- 1 in. dia. 1층 in. dia. 1 in. dia. Fig. 2 Ib /2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If the material of the beam has an allowable bending stress of Gallow = 175 MPa, determine the maximum allowable intensity w of the uniform distributed load. 300 mm 6 m 150 mm
A cross-section is subjected to a maximum shear of V=160 kN (see figure): Determine the centroid of the cross-section. Calculate the moment of inertia (I) of the cross-section. Determine the shear stress at point A in the cross-section.
PLZ STEP BY STEP MORE SPACIFICATION
Given: picture. Find: determine the reactions at the beam supports at A& D for the given loading.
Q1: A torque T= 4 kN.m G of steel core 77 GPa and G of aluminum 27 GPa, Determine: (a) maximum shearing stress in the in the steel core (b) the maximum shearing stress in the aluminum jacket. (c) the angle of twist at A.
A solid 0.78-in.-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the shear stress magnitude in shaft (3). a.)3.86 ksi b.) 3.51 ksi c.) 3.15 ksi d.) 5.38 ksi e.) 4.85 ksi
2. The bending moment acting on the triangular cross section of a beam is M = 3.6 kN m. Determine the maximum tensile and compressive bending stresses acting on the cross section. M 120 mm 60 mm-
Assiynment 11 20KN 3KN/m 4.5 m 1.5m 3 m SO mm Section of T-beam: 130 mm (50 mm The T-beam is subjected to the Toad hing shown. Cal culate the manimun skear stress in the beam, and draw shear stress distrib utyon over the cros secton at this critial location, where manimum shear stren occurs.
(b) A cooling tube having the cross section shown in Fig. Q1(b) is formed from a sheet of stainless steel of 3 mm thickness. The radii c₁ = 150 mm and c₂ = 100 mm are measured to the center line of the sheet metal. Knowing that a torque of magnitude T = 3 kNm is applied to the tube, determine (i) the maximum shearing stress in the tube (ii) the magnitude of the torque carried by the outer circular shell Neglect the dimension of the small opening where the outer and inner shells are connected. Hint: q - T 2A q=rt, T = Fr. Fig. Q1(b)
The beam loaded as shown is rectangular in cross-section having a width of 250 mm and a depth of 400 mm. Determine the following: 12KN/m 10KN/m 5m 3m a. The maximum flexure stress developed For the reaction at the supports - For the correctly drawn shear diagram (including location of zero shear For the correctly drawn moment diagram( including the magnitude of maximum moment) For the maximum stress developed b. *The stress developed at the fiber 50 mm from top of the beam, 3 meters to the right of support at A For the magnitude of moment at the section being considered For the magnitude of the stress
Two smooth cylinders are placed in the position shown. Cylinder A 1,000N and has a radius of 10cm while cylinder B has a radius of 8cm and weighs 750N. Cylinder A is connected by a 35cm string to the smooth wall C. What is the tensile stress in MPa, developed in the string if the diameter of the string is 10mm and angle beta is 25°? Bº ...