Q2) Implement three input NOR gate using two Combinatorial Logic Module (Actel FPGA) only.
Q: Find lo, 1₁, & /₂ using Mesh Analysis Le 1280°V 280 A LE I₁ www 1.SL I, j¹ I₂
A:
Q: Given Zo= 0.199290° pu, Z₁ = 0.175290° pu, Z₂ = 0.175290° pu, compute the fault current and voltages…
A:
Q: 13) You have a binary search tree (BST) with n elements, and you need to find the smallest 3th…
A: To find the 3rd smallest element in a binary search tree(BST),you can perform the following steps:…
Q: (b) Given K(s)G(s)H(s) = k s(4s + 1)(6s + 1) (i) Use the Nyquist Stability Criterion to determine…
A:
Q: Determine the gate output for the input waveforms in Figure 3-84 and draw the timing diagram. CDC A…
A:
Q: 1. Explain the different between active high and active low input with positive and negativ…
A:
Q: A 20-m-diameter spherical tank is to be used to store gas. The shell plating is 10 mm thick and the…
A:
Q: 26. An unbalanced star-connected load is supplied from a symmetrical 400-V, three-phase, three-wire…
A:
Q: 6- what does happen if a 2 MW load with the power factor of 0.7 is added to the first bus as follow?…
A: On adding the load at Bus-1, the load will draw more current from the source. If the KVA rating of…
Q: 7) Determine Ic, VcE, IB, Vg and VB (no order restriction) 39 ΚΩ ' 8.2 ΚΩ dia 9 18 V w 3.3 ΚΩ + VCE…
A:
Q: 5 A 2Ω 30 USI Μ in ΩΣ D2A
A:
Q: 3. Using Nodal Analysis, find Vo. ↑460'A jla 1.9 1.0 1280°V j'e 12×0 A Vo $ 20
A:
Q: For the transformer ratio arm bridges shown, C's=200 nF, Ra=300 M2, Rp= 20 G2, and Cp=20 nF. What of…
A: Given data, Capacitance, C's=200 nFCp=20 nF Resistances, Ra=300 MΩRp=20 GΩ
Q: 3.5 Obtain v, in the circuit of Fig. 3.54. 30 V (+ 2 ΚΩ Figure 3.54 20 V 5 ΚΩ +1 4 ΚΩ Vo
A:
Q: 3.5 The current i in the circuit of Fig. 3.48 is: (a) -2.667 A (b)-0.667 A (c) 0.667 A (d) 2.667 A…
A: Given: A series network with two resistor and two independent voltage sources. To find: Current i…
Q: 13. If you used 600 W of power for 60 h, you have used A. 36 kWh B. 3.6 kWh C. 10 kWh D. 1 kWh
A: Given data, Power is given P = 600 W. Time is given t = 6 hour.
Q: Resistive Voltage The supply across the terminals of this circuit is 170 V, 50 Hz. An ammeter is…
A: Given: A circuit, Supply voltage across the terminals is 170 V, 50 Hz. An ammeter is connected to…
Q: The circuit in Figure 1 is a balanced three phase system which has the following parameters:…
A: Line VoltageVab=Va-VbVbc=Vb-VcVca=Vc-Va
Q: Q. 17. In secondary ionization by photons: A. Electrons are emitted from the cathode. B. The photons…
A:
Q: Armature resistance of a 230V shunt motor is 0.60 and no load current is SA. When the rotor is…
A: Given data, Terminal voltage V = 230 V. Armature resistance Ra=0.6 Ω. No load current I0=5 A. When…
Q: 6.4 The following test results are obtained for a 30, 25 kV, 750 MVA, 60 Hz, 3600 rpm,…
A:
Q: 16) A 75 2 resistive load is preceded by a 2/4 section of a 50 2 lossless line, which itself is…
A:
Q: P4. The overall transfer function of a control system has G(S) == B If the response curve required 1…
A:
Q: current in R3 resistor
A:
Q: For the following circuit, G(s) = 1/s and H(s) = 1/(s+a)hotenst sosio 40=3H20=1,mio X(s) + G(s) H(s)…
A: Given data, Circuit is given below, Where, Gs=1s and Hs=1s+a.
Q: Q2 A PID controller is designed to control the robot leg, and the control system is shown in Figure…
A:
Q: 4. GIVEN: Z₂ = 6+j30, Z = 6.50-40°, Z = 3+j60, Tx = 20AZ-30° and Ty = 30AZ+20° Use your knowledge of…
A: Kirchoff's Law (KCL and KVL) and Ohm's law is very important to analyze electrical circuits. As per…
Q: 2. Use Thevenin's Theorem to find V (t) if f = 60 Hz. elle j³a 2145 A ↑ M 4.0 + Vx29 V/c ✓ in -earco…
A:
Q: I 12 Ω 1₂ 8 Ω 5 Ω –1 L- 320 Ο Is 13.7 A 6 Ω 1. 3 Ω
A: Note: Kirchoff's Law (KCL and KVL) and Ohm's law is very important to analyze electrical circuits.…
Q: Solve the circuit systematically and completely. Using the superposition concept, determine l₁ for…
A:
Q: TASK 3-Y-Y Three phase system The circuit in Figure 1 is a balanced three phase system which has the…
A: It is given that: Van=2202∠0° VVbn=2202∠240°=2202∠-120° VVcn=2202∠120° Vf=50 HzR=R1=R2=R3=100…
Q: Combinational logic circuits' results are entirely dependent on their inputs.
A: Combinational logic circuits : There are mainly two types of logic circuit one is combinational…
Q: A 3-, 400-V symmetrical supply feeds a star-connected load consisting of non-reactive resistors of…
A:
Q: 2. PRE-LAB WORK 1. Given the logic diagram, truth table and pulse input for JK flip-flop, determine…
A: Types of Triggering Positive Edge Triggering Negative Edge Triggering Level Triggering
Q: Q) If an 800-ft span normally has a sag of 20 ft at 60°F, the sag in the summer at 90°F would be A.…
A:
Q: Q2-The electric flux density inside a cube is given by: a-D = âx (3 + x) b- D = ây(4 + y2) Find the…
A: Given data: D¯=a^x(3+x) we know that,…
Q: The circuit shown in the figure is connected to an AC generator that supplies 5 V (RMS value). R = 5…
A: Given data Ammeter reading, I=1 mA Resistance, R=5 kΩ Supply voltage, Vs=5 V Voltmeter reading,…
Q: Find the loop currents i1, i2 and i3 in the given circuit using Mesh Analysis. 0923/01/0/1 R2 2002…
A:
Q: 2 Ω I 5Ω 10 Ω 25 V Ε Σ4Ω 2 Ω I 7 ) 50 v
A: The given problem is from mesh analysis. The detailed solution is given in the next step
Q: 1 Calculate 11001.11₂ +11010.12.
A:
Q: Q. 11. In a vacuum, if there is a long gap between the electrodes, prior to breakdown a small…
A: In a vacuum, if there is a long gap between electrodes, prior to break down a small current flow…
Q: Q1: Find the value of v,in following the circuit assuming the op-amp is ideal (10 Pts) 9V 8 ΚΩ 5 V 6…
A:
Q: 1- In a buck DC/DC converter: V₁ = 100 V, R = 82, D = ton = 0.8, f == 20000 Hz, L = 200 μH, C =…
A:
Q: The light, R₁, indicates when the device is running. A timer in Device X opens the switch 5 seconds…
A: Note: Only active power will be available in purely R Load Only Reactive power will be available in…
Q: a. Find the total admittance and impedance in polar form. i, 3 sin(377r+ 60°) R120X₂20 Xcsn
A: Given data:
Q: (a) Define Noise Immunity and Noise Margins in CMOS circuits. (b) Describe some of the key factors…
A: Noise immunity: It is a measure of the capability of a logic circuit reacting to the undesirable…
Q: 2. Using Kirchhoff's Rules/Laws, determine the current I₁, II and I shown in the diagram below. Use…
A: The given circuit diagram is shown below. The given values of the resistances are written below.…
Q: Q₁: Determine the Fourier series expansion of the periodic function f(t) shown below. By giving an…
A:
Q: 8 Translate the BCD words 0111 into seven-bit words of the form ABCDEFG (display with seven…
A: 8. Given, BCD code is 0111. We need to determine the seven bit word of form ABCDEFG (from the…
Q: 60 u(-t)V 干 30 10 20 3. 120 V -2) VC(t) ve İC(t) 'yi bulunuz. M 40 5 u(t)A + + Vc(t) 45V -m F Icht)
A:
Step by step
Solved in 2 steps with 2 images
- logic circuit diagram for fabinaaci counter that gives output in fabinaaci sequence.upto 2 digits please mentions the gates and ics used in circuit.Instructions A designer at Channel Microsystem needs to design basic logic gates with the use of PN junction diodes, light emitting diodes (LED), 5-V power supply and resistors. The logic gates are to be tested through random input logic pulse and verified in time domain analysis. A O A O Out Out BO BO OR NOR A O Out Out BO в о AND NAND Figure 1 HIGH '1' DIODE-DIODE LOW '0' LOGIC Out GATES во Figure 2 Figure 1 illustrates the combination of logic gates to be developed using diode-diode logic. Figure 2 describes the simulation testbench setup in verifying the operation of the logic gates developed through diode-diode logic. Design and verify the diode-diode logic with low5) Draw the circuit diagram using diode and write the truth table of a logic gates whose output will be the logical OR operation of two inputs.
- ) The input waveforms in are applied to logic circuit in figure below. Determine the output waveforms. B G2 C C D D EImplement the logic circuit in Figure 2 using only NAND gate A B C XQ2/A) Design 8x1 multiplexer using 2x1 multiplexer? Q2 B)Simplify the Logic circuit shown below using K-map then draw the Simplified circuit? Q2/C) design logic block diagram for adding 12 to 5 using full adder showing the input for each adder?
- The circuit shown in the figure is an example of A.) AND gate b) SPDT electronic switch C) inverter D) OR gateA certain digital circuits designed to operate with voltage levels of -0.2Vdc and -3.0Vdc. If H= 1 =-0.2 Vdc and L =0 =-3.0 Vdc, is this positive logic or negative logic ? H=+5.0Vdc. and. L=+1.0Vdc What are the voltage levels between fall and rise times are measured? What is the value of Duty cycle H if the waveform is high for 2 ms and low for 5 ms?Draw the logic diagram and transistor implementation for a (2-2-2) AOI.
- Q1) For the circuits shown in figures 1 and 2: 1. What is the function of output? 2. Find the max. and min. Vol. value? 3. Determine the static power (avg.)? 4. Design equivalent logic circuit by CMOC logic circuits? Use VDD= 10 V. Vr.o=1V. Vru-1V. (W/L)o= (5/2), (W/L)L (20/2), RD = 40k, KL = 10P A/V^2 and KO = 40pA/V`2? Figure 1 5 VDD RD Figure 2 बदना देBelow is an example of an NMOS logic circuit. For all of the MOSFETs in the circuit below, assume V = 1 V and k = 50 mA/V². th W R₂ = 5600 PEETHIPPIN R₁ - 4700 M3 M₁ M. 0 a. Indicate and verify the state of each MOSFET and V for the following input combinations. Fill-out the table below for each assumed state of the MOSFET for every input combination. Use R approximation for linear operation and three significant ds(on) figures for the voltages. 오 Ao SV why(c) Identify and draw the simplified logic circuit for Figure Q5(c) by using only a single (1) logic gate that can be applied to replace the whole circuit. Figure Q5(c) X