Q2: Draw a cross section in a tie beam with dimensions of 50cm height and 30 cm width, given that the reinforcement is 50 16mm top and bottom and 10 10mm @ 25 cm stirrups. Use scale of 1:10.

Q: Sketch thefollowing figure ,orthographic view ( using catia )  Metion the top view side view and…

A: From figure.......

Q: Convert 10 in to centimeter' 1 Add file

A: answer = 25.4 cm  explanation is given in below step

Q: Object 3. a. Replicate the front, left and top side views given using the 1st angle projection. Add…

A:

Q: Draw top, front and right view of the following isometric views

A: Top view

Q: Show Isometric View. Use Dimlinear for measurement

A: Hi! As per the honor code we are not allowed to provide file or link of the file. We are only…

Q: 2.

A: FRONT VIEW observe the diagram in the direction of the arrow and draw the shorter side of the box…

Q: III-3-2 Graphic elements 1- Cutting tabs They make it possible to fix. 2- Margins and frames The…

A: Cutting tabs play a crucial role in securing various parts of a construction or model together. They…

Q: 3. Given two Orthographic views of an object, construct an Auxiliary view of the indicated ( —P)…

A:

Q: Draw the Orthographic views ( Front view and top view) from the following Isometric view Free Hand…

A:

Q: Given the multiview projection of the solid, draw its isometric view.

A: Solution- The given diagram is shown below. To Determine,  The isometric view

Q: Generate isometric drawing from multiviews using drawing tools or free - hand. Use approximate…

A:

Q: Show Isometric View.

A: Answer  We can obtain the isometric view from given views in Autocad using the following steps 1)…

Q: Given the multiview projection of the solid, draw its isometric view. HRP FRP FRP PRP ㅏ

A:

Q: DRAW ISOMETR VIEW

A:

Q: Draw the Orthographic Projections (Top View, Front View, Side View) For the Shapes Shown Below,…

A:

Q: What type of drawing is shown (the bottom center of the object closest to the viewer comes to a…

A: A) 3 View incorrect. -> 3 view or orthogonal views are the projections when seen from a fixed…

Q: 120 22 56 34 44 RS O-2 Holes Top view Isometric view 36 64 40 26

A: Answer:- A- A Section and top view:

Q: Draw the multiview projection of the given isometric figure. L HRP FRP L L FRP PRP 1. Discuss how…

A:

Q: SM Ø HOLES 10M A12.5M "SM 125M BOM FRONT VIEW SIDE VIEW

A:

Q: L (Isometric Drawing) J 56 104

A:

Q: Third angle projection is displayed. Draw the visible feature lines of the right view and any hidden…

A: In right view there is no hidden lines

Q: 5 TOP 10 8 FRONT ? Isometric View RSV

A:

Q: 50. Complete an interpretation drawing that shows the permitted angularity tolerance zone. 200 A 62…

A:

Q: ate the centroid of the shaded area. Y 20 mm 45 mm 20 mm L. 54 mm

A: To find centroid

Q: Draw the the 3 principal views and auxiliary view (like in the second photo)

A: Auxillary view: The orthographic view drawn taken according to the line of sight which is not…

Q: structural drawing   please indicate a details in this image

A: The structural diagram is shown in the above figure. We have to indicate a details in this image.

Q: There are a couple errors in the multi-view drawings below (the isometric is accurate and assume any…

A:

Q: P4-7) Create an orthographic projection of the following object. Draw the three standard views. SLOT…

A: This view is Orthographic projection. Model after completing in AutoCAD has been presented in next…

Q: SKETCH AUXILIARY VIEW. SHOW ALL VISIBLE AND HIDDEN LINES.

A: An auxiliary view is simply known as the “helper” view because it shows the slanted part of the…

Q: answer whether the multiview projection matches the isometric drawing depicting a valid solid.Answer…

A: The answer is yes, multiview projection matches the isometric drawing The reason is that the…

Q: SUBJECT: CIVIL DETAILS: ISOMETRIC DRAWING.

A:

Q: Q3. Draw projections of the following two points A & B on the same XY line. Keep a gap of 50 mm…

A: drawing projection is depend on the quadrant is given in the problem . their is 4 quadrants in the…

Q: Draw the figure below in AutoCAD, take a screenshot of your work and paste it to the spaced…

A: The following image shows the given figure drawn in autocad with dimensions along with name.

Q: By using the figure below, reproduce this by using the relative rectangular coordinate entry. You…

A: Required To reproduce the given figure in question and to give the commands used to draw in AutoCAD.…

Q: 1. What command do you use to display AutoCAD Point Style Box? (KIND/ DDPTYPE/ DS) 2. What is the…

A: Answer 1=> The Point Style window will open with a list of available point styles if you type…

Q: Use the following 1- Fill the NGL values in the profile view. 2- Draw NGL using a vertical scale…

A: NGL: The Natural Ground Level (NGL) is defined as the unmodified level of the ground or land.…

Q: Subject: Engineering Drawing or AutoCAD Instruction: Draw the D Drawing (ometric View) of the…

A: Isometric view is the 3 dimentional view in 2D plane.  Below is the attatched isometric view of the…

Q: Measure the red line using the given figures (please answer in appropriate format for the type of…

A: Let’s take the architect scale as follows:

Q: TOP VIEW 130 R30 STILLST R30 20 3X 024 65 FRONT VIEW -R30 1242- LL Ø16 R22 44 RIGHT SIDE VIEW

A:

Q: show

A: angle = 188°59'30''

Q: Top, Front and Side view of this sketch.

A:

Layout and Design

The layout is the process of marking all the building components on the land from the prepared plan. The layout of construction includes transferring the whole plan of foundations, boundaries of the structure, centerline of the wall, and all other important structural parts on the ground along with the length and width so that the components of buildings can be excavated properly. Designing is the process of establishing the concept of the building on paper in a properly engineered manner.