Q1/B/ Discuss the operating of laser at loop gain=1. What happen to the output of the laser when the loop gain is less or greater than one?
Q: 3) Consider the Zener-diode voltage regulator shown below. Suppose you design this circuit to drive…
A:
Q: In a single-phase semi-controlled rectifier, if the firing angl degrees and the input voltage is…
A: To answer: obtain the Dc voltage
Q: What are the main differences between the D-MOSFET and E-MOSFET amplifiers?
A: MOSFET The metal oxide semiconductor field-effect transistor (MOSFET) is a type of transistor in…
Q: What are the colors of a 4- bands resistor of a value R= (10 +or- 0.5) ?
A: R= (10 +or- 0.5)
Q: Consider the V(x)= Case c) for a go back Vo step if d) (alculate the a) case E <Vo b) Calculate the…
A: Given the step potential is (a) To find the reflection coefficient for the case E<V0. We have…
Q: Band Resistor color coding, and solve any three examples of your choice?
A: Band resistor color coding is used to find the value of the resistor easily. The color code is…
Q: (a) Calculate the directivity for n = 1, 2, and 3
A: Since you have asked four questions, we will solve the first question for you. If you want the other…
Q: How is gain determined for operational transconductance amplifier? wwww ww wwww a) two rates of…
A: This is a question from Analog Electronics. Operational Transconductance Amplifier: It is a device…
Q: What is the normal range for the value of phase constants? For example, would a value of 67.12 rad…
A: For a complete oscillation, phase difference is of and path difference of one wavelength.
Q: Question a) A stepper motor has a step angle of 1.8° and it is driven at 6500 pps. Analyzing the…
A:
Q: What are the disadvantages of a half wave rectifier?
A: A half wave rectifier is used to convert half of the cycle of alternating current to direct current.…
Q: What is used in PCM to represent the value of the modulating signal?
A: Pulse code modulation is a method used to convert analog signals into digital signals. The modified…
Q: 2- Design and simulate double Zener diode AC Clipping circuit, draw the input and output diagram.
A: Let us design a double Zener diode AC Clipping circuit of output 5.7V AC in accordance to any input…
Q: This is #4 on the worksheet. How much energy will a 2.5 W laser use in 12 seconds? Your answer: O…
A:
Q: A i i B ! ! ! ! !
A:
Q: In the figure below the carrier signal Ac cos(@ct) has an amplitude of 20 volts and the diode…
A:
Q: An FM signal has a deviation of 3 kHz and a modulating frequency of 1 kHz. Its total power is 5 W,…
A: FM signal.
Q: Write the loop rule for each designated loop.
A: For writing loop equation: direction of current is taken as positive. all the potential adds up to…
Q: What is the angle from we get the maximum c voltage in three phase
A:
Q: step by step solution and explain would be helpful to understand
A: Step 1: Step 2: Step 3: Step 4:
Q: Problem H a) Determine the closed-loop 3-db bandwidth. The op amp has a unity-gain frequency of 0.8…
A:
Q: The output voltage of an op amp is -7 V when the noninverting input is 1 mV. If the open-loop gain…
A: Output voltage Vout = - 7 V Noninverting input Vnon = 1 mV = 1 × 10- 3 V Open loop gain of op amp A…
Q: Q. 21. Write a program to output square wave of 1 kHz frequency on the SOD pin of 8005 Count 70.21…
A:
Q: At what point the mull point will be obtained on a meter-bridge if the ratio of resistances im the…
A: We have to find: Position of null point We have given data from the question is: R1R2=23
Q: B1. For the CRO square voltage waveform is shown in Figure. The 'time/cm' switch is on 40 ms/cm and…
A:
Q: 130° C 500 N 50°
A:
Q: 5. The following figure shows an inverting amplifier that can have high gain without resorting to as…
A: Solution attached in the photo
Q: 2. What design parameters of the three-phase half wave rectifier? 3. When you design 30kW rectifier,…
A: Answer(2):- The system of 3-phase voltage source PWM rectifier concludes main…
Q: Define the limitations of difference amplifiers and explain that when it does not meet the…
A: Differential Amplifier is a device that is used to amplify the difference in voltage of the two…
Q: Estimate the energy difference (cm ) between the v 0, J= 0 level and the v = 1, J = 0 level. Based…
A: For pure vibrational energy levels, we can write, εv = (v + ½ ) ϖe – xe (v + ½ )2 ϖe - - - (1)…
Q: Color code value as 2 k Ω± 5% Color coding of a read resistor do you do?
A: given :- color code value = 2 k Ω ± 5 % = 2000 Ω ±5%
Q: Assume that it takes 4 microseconds at normal body temperature for the polarized sodium ions to…
A: t=4 microseconds R1 100 Ohms R2=0.1 Ohms
Q: Explain the differences observed in the relationships between the lasing power and pump power for…
A: A laser could emit short pulses if the loss of an optical resonator is rapidly switched from a high…
Q: a: G. Write a note on signal amplifiers.
A: Solution given in the next step...
Q: nt the egulvalent reststance ot teradnals 2termdnals an Jow: 10-2
A: The equivalent resistance between terminal a and b can be calculated by grouping the resistances in…
Q: What is the open loop gain of op amp, if the if the two inputs are V1 and V2, and output is Vo? w
A: Let V1 has positive charge and V2 has negative charge. The op amplifier with two inputs and one…
Q: For the 3- input And gate, determine the output waveform in relation to the following inputs. 1)…
A: Let us connect the 3rd terminal to B. A=(00100100100100100) B=(11111111110000000)…
Q: Why the signal generated by the resistance strain gauge cannot directly use the current amplifier as…
A:
Q: 7. What is the RMS voltage of a square wave with a 50% duty cycle that swings between ±5?
A:
Step by step
Solved in 2 steps
