Q12) The gain of vertical deflection amplifier in CRT is 90. If an input signal of 110mV is applied, it will produce electrical field of 33V/cm and vertical deflection of electrons beam on the center of plates of 4.31x10³cm with an angular deflection given by arctan (0.0137). The electrons enter the plates with a velocity of 3.2479x10 cm/sec, and deflection sensitivity of 0.055cm/V. Determine: 1) The dimensions of vertical deflection plates (long, a part (1,d)}. 2) The distance from the end of deflection plates to the screen. 2.5cm, 0.3cm, 38.49cm)

Q12) The gain of vertical deflection amplifier in CRT is 90. If an input signal of 110mV is applied, it will produce electrical field of 33V/cm and vertical deflection of electrons beam on the center of plates of 4.31x10³cm with an angular deflection given by arctan (0.0137). The electrons enter the plates with a velocity of 3.2479x10 cm/sec, and deflection sensitivity of 0.055cm/V. Determine: 1) The dimensions of vertical deflection plates (long, a part (1,d)}. 2) The distance from the end of deflection plates to the screen. 2.5cm, 0.3cm, 38.49cm)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

8...EDC
find the average power consume by RL for both fullwave and halfwave rectifier circuit.
In the given circuit, D1 is Silicon diode and D2 is a zener diode with breakdown voltage of 6.8V. Assuming RC time constant of circuit >> T. Find the Maximum and Minimum value of the output waveform.
Choose the correct answer
1.Find condition to know Diode on or off, Von = 0.7V. 2 Find relative equation between Vo and Vin
6:39 Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as silicon and D2 as germanium diodes. Input Vpp=20V, V1=5 V and V2=9 V. www Vin Vout Maximum voltage of output waveform Minimum voltage of output waveform
INCLUDE ALL THE DECIMALS.
Using a constant voltage drop of 0.7V across the diode in forward bias, find the current I and the voltage V in the circuit shown in Figure-Q8. 2 kQ 8 Vo-WW-K Not 5 VO Figure-Q8 -2 V OV 6 ΚΩ
Using a positive Clamper with positive biasing voltage Circuit, with an AC voltage of Vi = 20v with a frequency of 60hz, a value of 500n for the Capacitor, a silicon diode, biased voltage voltage of 5 volts and a resistor with the value of 300 ohms. Find the current on the resistor at a simulation of 20ms in mA. Vm 2Vm R V,m Vo -Vm V, Input Waveform Output Waveform Positive Clamper with positive reference V, www
For a certain 12 V zener diode, a 10 mA change in zener current produces a 0.05 V change in zener voltage. The zener impedance for this current range is O a. 50 Ob. 10 - c.0.1 Ω Od. 10 Q
The waveform given below is observed on the screen of a CRO. If the time/div switch is set at 10 µsec and the volt/div at 200 mV, the frequency and peak to peak voltage are, respectively. -1.5 -1 -1- -2- 2 1 1 1.5 2
Q.2 Te diodes m the Cir Cuit of 6iG. below are icdead , Drow the Tran sfer characteristic for 2ovSVi s 2ov ? Di Ri R3 lov