Q10. If the impedance of a circuit = 20 – j10 1. if a voltage source is connected across this impedance, which if the following statements is correct? O The power factor will be lagging O The current will be leading the voltage o The current will be lagging the voltage Voltage and current will be inphase

Q10. If the impedance of a circuit = 20 – j10 1. if a voltage source is connected across this impedance, which if the following statements is correct? O The power factor will be lagging O The current will be leading the voltage o The current will be lagging the voltage Voltage and current will be inphase

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.2P: Convert the following instantaneous currents to phasors, using cos(t) as the reference. Give your...

See similar textbooks

Similar questions

Find the Apparent Power (rounded to 2 significant digits) for the following circuit: VT = 120V RMS, R1 = 1k0, R2 = 8200, XC1 = 1202, xC2 = 5002, XL1 = 3300 C1 R1 R2 C2 L1 24VA O 1.9VA O 15VA O 6.5VA
5 The voltmeters in the figure measure RMS voltages. If V, = 23 V and V, = 14.5V what is V3? %3D C R eee V2 V3 23 V None of them 8.5 V 4.5V 37.5 V O 14.5 V
Please show you detailed solution Number 10 A voltage of 250 volts at 50 Hz is impressed on a circuit having a 60-ohm resistor, 35-?F capacitor, and a 0.25-henry inductor in series. Determine power factor. A. 0.979 C. 0.924 B. 0.862 D. 0.707
If the voltage V, = 800 mV, then the current flowing in the load I, is: %3D -j20n Select one: O a. None of these O b. Is 100 <-90° mA O c. Is 5.0<.-90° A O d. Is 5 <90° mA ell
Q5] find the current of the resistance 1892 if the value of the source is 7.4sin(100nt-44) volt Give the right choice HH 1mF ww 0.093H R1 www 180 R4 1402 3.9mF 13.100, 78.163⁰ mA 14.100, 78.163⁰ mA O 15.100, 78.163⁰ mA ·2 V1
Determine the DC currents (la. lc and I) and dc junction voltages (Var Ver and Vca) la-Blank 1 mA, le-Blank 2 mA, I-Blank 3 mA, Var Blank 4 V, Vcr Blank 5 V and VcB - Blank 6 V Use 2 decimal places. Use the following values. VBB= 3V RB= 5kOhms Rc=232 ohms Vcc =18 V BDC=65
6. Determine the rms current I as shown in figure 1. Source voltage is already in RMS value (Answer must be in polar form and should be in 4 decimal places). -j4 N j1.5 A B 4 0 A 200/30° V -j2 N: jIN Figure 1.
6. Determine the rms current I as shown in figure 1. Source voltage is already in RMS value (Answer must be in polar form and should be in 4 decimal places). -j4 N j1.5 N B 4 N 200/30° V -j2 N= jI N
Assume that the load resistance can be varied between 0 and 4000 Ω andthat the capacitive reactance of the load can be varied between 0 and−2000 Ω. What settings of RL and XL transfer the most average powerto the load? What is the maximum average power that can be transferredunder these restrictions?
what is average power delivered to R4
This course Time left 0:48:03 Find the value of i2, i4 and i5 if i1-3A, i3-1A and i6-1A. 10 oh 20 ohm 15 ohm 30 ohm S ohm Select one: O A. 4,24 O B. 21,2 O C. 4,24 OD 2,12 ge Next page 10:36 AM E di) EIG
2. A triangular voltage source has a peak value of 10 V. What is the computed RMS value of this source? a. 3 V b. 4 V c. 5 V d. 6 V 3. In Question 2, if the source is measured by an analog meter, will it show the correct RMS value? a. Yes b. No