Q1. A rectangular water tank of length 10m and width 6m has a free surface 15m above a 300mm diameter sharp edged nozzle that discharges to atmosphere. Ignoring friction, calculate: a). Velocity through the nozzle (m/s) b). Actual discharge of the nozzle (discharge coefficient of nozzle : 0.96) (m³/s) c). Mass flow rate of the nozzle (kg/s) %D

Q1. A rectangular water tank of length 10m and width 6m has a free surface 15m above a 300mm diameter sharp edged nozzle that discharges to atmosphere. Ignoring friction, calculate: a). Velocity through the nozzle (m/s) b). Actual discharge of the nozzle (discharge coefficient of nozzle : 0.96) (m³/s) c). Mass flow rate of the nozzle (kg/s) %D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Water at 100 kPa flowing in a 10-cm-diameter pipe passes through a 2-cm-diameter flow nozzle equipped with a manometer across the nozzle. 10 cm 8 cm S = 10 12 cm S- 13 16.0 Determine the flow of water through the nozzle if coefficient of discharge is 0.7 a.) 1498 mL/s b.) 1433 mL/s c.) 4488 mL/s d.) 4539 mL/s e.)
A liquid whose specific gravity is 2.0, is flowing in a 150mm diameter pipe. The total head at a given point was found to be 17.5m. That point is 3m above the datum and the pressure in the pipe is 65.6KPA. Compute the discharge in that point of the pipe. A) No Answer among the choices В 24.31 L/s C) 19.28 L/s D 29.05 L/s E 32.56 L/s
A venturi meter with 150 mm diameter at inlet and 100 mm at throat is laid with its axis horizontal and is used for measuring the flow of oil of sp. gr. 0.9. The oil mercury differential manometer shows a gauge difference of 200 mm. Calculate the discharge in liters/s. Assume the co-efficient of meter as 0.98. a. 56.4 b. 25.7 c. 27.8 d. 63.93
A closed cylindrical tank 3m high and 1m in diameter contains 1.2m of oil (SG = 0.8), 1m of water and air under a pressure of 16 KPa. A 125mm diameter orifice is placed at the vertical side of the tank, 300mm from the bottom. Determine the actual discharge at the orifice if C = 0.94. Hide answer choices A 98.61 L/s B) 103.01 L/s C No answer among the choices 96.83 L/s E) 92.69 L/s
A 75 mm diameter nozzle is shooting out water from the pipe. Assumenegligible head loss, determine the following:a. velocity at point Ab. discharge at the nozzlec. height of the jet from the nozzle (“h”) h1=1.8 m D=150 mm p=100kPa
ire hose has 100 mm diameter which reduces to a 20 mm nozzle discharging at 10+X m/s. (X= 16)Calculate the following: a) How high the water can reach if the nozzle is aimed vertically? b) What is the pressure inside the hose? c) How much extra force will be created at the reducer due to velocity change?
SN=23 SUPPLEMENTARY QUESTION The figure shows two reservoirs connected by a pipe. The discharge rate in the pipe is known to be equal to SN/100 (m/s) (where SN is the sum of your student number). Calculate the height of the second reservoir (H2), and the pressure head, velocity head and elevation head at point 3 (mid-point of the pipe). Hi-300 m Ha datum A SN/1000 L- 100 x SN (m) D 0.3 m
The fluid in the figure is water, with the surface 10m above the datum. The pipe is 15cm in diameter and the head losses are as follows: from 1 to 2, 0m; from 2 to 3, 0.60m; from 3 to 4, 2m; and from 4 to 5, 0.30m. 1.Determine the velocity of flow in the pipe in m/s. 2.Determine the discharge Q in m^3/s. 3.How many centimeters above the center of the pipe will water stand in piezometer tube 3? 4.How many centimeters above the center of the pipe will water stand in piezometer tube 4?
300 mmg 100 mmø H2O, 2) 500mm A 100mm diameter venturi meter is installed in a 300mm diameter horizontal main pipe as shown. If the deflection of mercury (SG = 13.6) at the manometer reads 500mm, determine the discharge in the system assuming no head loss.
PROBLEM 10: A circular orifice is located 5m. below the water surface. If the tank is large and the diameter of the orifice is 5 mm, calculate the discharge in m/sec. if the coefficient of discharge is 0.60. a. 0.00812 c. 0.00012 b. 0.00140 d. none of these
The nozzle which furnished the water to a certain hydraulic turbine 275mm in diameter and hascoefficients of velocity and discharge of 0.975 and 0.96, respectively. The nozzle is supplied from a60cm pipe in which the water approached the nozzle with a total head of 330m. Compute thefollowing:a. Energy per second delivered by the jet to the turbine.b. Energy measured in hp lost in passing through the nozzle.
A closed cylindrical tank 3m high and 1m in diameter contains 1.2m of oil (SG = 0.8), 1m of water and air under a pressure of 16 KPa. A 125mm diameter orifice is placed at the vertical side of the tank, 300mm from the bottom. Determine the actual discharge at the orifice if C = 0.94. A 92.69 L/s B 96.83 L/s 98.61 L/s D No answer among the choices E 103.01 L/s