Q1/ The beam shown in figure below consists from steel and aluminum, find the maximum load that can be applied if the stress in steel not exceeding 80MPa and in Aluminum 30MPa. Est = 210GPa and EAlu = 70GPa

Q1/ The beam shown in figure below consists from steel and aluminum, find the maximum load that can be applied if the stress in steel not exceeding 80MPa and in Aluminum 30MPa. Est = 210GPa and EAlu = 70GPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Q1) A beam with a cross-section shown in figure 1 is loaded in such a way that the maximum moments…

A: Write the given data with suitable variables. σ1=4 ksi=4000 psi1000 psi1 ksiσ2=10 ksi=10000…

Q: a triangular distributed horizontal force of peak intensity (see the figure). The length of the

Q: 1- The simply supported beam in figure below has a rectangular cross section 120 mm wide and 200 mm…

Q: A wood beam carries the loading shown in the figure calculate the magnitude of the bending stress…

Q: A simply supported beam carries a concentrated load at the center which fluctuates from a value of W…

Q: blas 4 For the beam section shown in figure if Q=1 kN. What is the shear stress(es) in plane 20 mm…

A: Draw the beam cross-section into different parts.

Q: below, find the maximum shear stress and maximum normal stress

A: to find Maximum shear stress and maximum bending stress.

Q: 1. Compute the stress (ksi) in each member of the Warren truss as shown in the figure. Indicate…

Q: A bending moment of M=150 kips-in is applied at the cross section of beam shown in Figure Question…

Q: A wood beam carries the loading shown in the figure. Calculate the magnitude of the bending stress…

Q: Two uniformly distributed loads of w = 3300 lb/ft act on the simply supported beam shown in Figure…

A: A moment of inertia is the mass of the body when the body is rotating on an axis (resisting any…

Q: The beam shown below has a cross section of channel shape with width b=D400 mm and height h=80 mm,…

A: Answer: The maximum tensile and compressive stresses in the beam are 64.68 MPa and 16.36 MPa…

Q: Q-5 Find the maximum tensile and compressive flexure stresses for the cantilever beam shown in fig…

A: Given Data The uniform distributed load acting on the beam is: W=4 kN/m The Length of the beam is:…

Q: Give the following problem a try. If you get stuck, here is one way to work it: Essential Solution…

A: The applied force is .The dimension are The allowable shear stress is

Q: 2. Given the box beam shown below, and concentrated load P=3500#. a. What is the magnitude of the…

Q: am is subjected to a force of 1 S-section of the beam is 75cm the stress in the beam.

A: GIVEN:F=150KNA=75cm2

Q: AB beam three rectangular planks obtained by gluing and as shown in the figure has been loaded.…

A: Free Body Diagram of the body Now we will calculate the support reactions,As we can see…

Q: 4 - A rectangular block is loaded with a 180 kN axial force and a moment M, as shown in the figure.…

A: Given data:- Axial force =180 kN the maximum allowable tensile stress = 50 MPa To find:- the…

Q: c) Find the stresses in the concrete and the reinforcement for the following applied moments: (i) -…

Q: The semicircle shown in Figure 2 carries a load F = 1 kN at its free left end and bending moment M =…

Q: 1.8 kN 3.6 kN Since the safety normal stress 40 mm of the wood used for the beam and loading…

A: Given data: The safety normal stress in the beam is σ = 12 MPa. The width of the beam is b = 40 mm.…

Q: As shown in the figure below, determine the internal loadings at points D and. Consider the weight…

A: given: FN = 70lbs SN = 50lb/ft

Q: A beam made of Al 2014-T6 aluminum alloy is loaded by an oblique bending moment of M= 5 kN.m as…

A: Solution: a) Centroid of the cross-section y¯ can be calculated by, Let area A1 = 90×10=900mm2…

Q: beam at quarter of the

A: Given ,

Q: (a) If the beam A-D has a rectangular cross section as shown in Figure. 3.1 - (i), determine the…

A: Given:Diagram with detail is providedAllowable tensile stress = 7.5 MPaAllowable compressive stress…

Q: For the cantilever beam arrangement shown below, address the following: (a) Determine the forces…

Q: AWT230 x 26 standard steel shape is used to support the loads shown on the beam in the figure. The…

Q: Let's consider a canteliver beam, fixed supported at A, and subjected to the shown load. Determine…

Q: 52 mm, 28 mm- Figure Q1 (a) 2600 mm 620 mm

Q: For a steel circular cantilever beam, 10mm in diameter, 700mm in length with an applied load of…

A: M= (3/4 My + 1/3 Mp)My = 24543.5 N.mmMp = 41666.66667 N.mmYield strength= 250 MPad = 10 mmy = d/2F =…

Q: a) Calculate the reaction forces in terms of F and theta. b) Calculate the internal shear force and…

A: Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: a) A lm long cantilever steel (E = 200GN/m²) beam has a cross-section as shown in Figure 2.1. The…

A: For beam L = 1m E = 200 GN/m² Load = 1 kN θ = 45°

Q: Q.2 A square timber beam used as a railroad tie is supported by a uniformly distributed loads and…

A: Given: ununiform distributed load→W1=24 KN and W2=48 KN Hence upward uniform distributed load:…

Q: OA =240 MPå raw the T and M diagrams. alculate the force Pa that will start flowing in the beam.…

A: Givenyield stress σy=240MPa

Q: A cantilever beam has a cross-section and concentrated loads P1 = 30 kN and P2 = 10 kN, as shown. a.…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

Homework 3:
Q1/ The beam shown in figure below consists from steel and aluminum, find the
maximum load that can be applied if the stress in steel not exceeding 80MPA and in
Aluminum 30MPA. Est
= 210GPA
and Eatu = 70GPA
3PKN/m
Steel
40тm
220тm
Aluminum
6m
Steel
40тm
100mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q1 A steel beam of I cross-section is simply supported on a span of 4m. Find the safe uniformly distributed load the beam can carry if the tensile stress is not to exceed (60) N/mm2. Also find the maximum compressive stress.
Calculate the normal stress and shear stress acting on an element G, 150 mm from the top surface of the beam, in the section to the left of the point load (water tank load) as shown in the bottom figure and then determine the principal planes and the principal stresses.
What is the maximum length of a uniformly loaded, simply supported beam based on the maximum allowable stresses, its normal stress of 90MPa and its shear stress of 100MPa? The uniform load is 10kN/m. The area is b = 20mm and h = 80mm
Q3: A hexagonal cross section bar as shown in Figure (2) below, is used as a simply supported beam. The beam carries a central load of 60 kN. Draw the shear stress distribution diagram for a section of the beam at quarter of the beam length from the left hand support. Figure (2) 25 mm 30° 30°
From the given figure below, determine the minimum width of the beam if the flexural stress is not to exceed 150MPa. Assume height of beam is 300mm. 40KN k pº RB=320kN 280KN 2M 65100/m -40kN -BOKNM 4m 20KN 도 20KN qu 520 kNm RD = 260KN V-DIAG -260kN M-DIAG
A steel beam of I cross-section is simply supported on a span of 4m. Find the safe uniformly distributed load the beam can carry if the tensile stress is not to exceed 26 N/mm2. Also find the maximum compressive stress.
Question Four A beam of the cross section that is shown in Figure a was supported by two rigid supports that tilt by 45° from the horizontal ( see Figure b). The own weight (w) of the beam is 1.5 kN/m. allowable tensile stress (o), = 50 MPa. Calculate the maximum length (L) of the beam that can be supported. 20 cm ... 45 If the maximum %3D 40 cm 15 cm 10 cm (а) 450 (b)
Total Change in length?
2- Please solve this question in detail. Thanks
90 mm, 90 mm 170 mm M 50 mm 37.5 mm Figure Q1 (a)
A 3-in. by 6-in. steel (E-29,000 ksi) bar (4-foot long) is subjected to the loads shown. Calculate the combined stresses at points A and B (be sure to indicate either tension or compression). Remember, the bar is bending in the strong direction so calculate your I accordingly. 1(1/12) (B)"(H) S=l/c A B. 6" 10,000 lbs 45,000 Ibs
(ohsm 2) b. throps A simply supported beam has a rectangular cross-section of 50 mm wide and 120 mm deep. It is loaded as shown in Fig. 3b. Calculate the maximum stresses and draw the stress distribution diagram. The weight of the beam is assumed negligible. mot dit to sbutingsm s A - 2 m edband Im 10 kN B Fig. 3b 136 say xovbizon 2 m C