Q1/ The bar shown in Fig. 1 is subjected toa tensile load of 50 KN. Find the diameterof the middle portion if the 'stress is limitedto 130 MN/m². Find also the length of themiddle portion if the total elongation of thebar is 0.15 mm. Take E=200 GN/m².50 kNFig. 140 mmdia.+Px250 mm40 mmdia50 kN

Answered: Image /qna-images/answer/a60b92d5-6d53-461a-8426-3a334c05de46.jpg

Q1/ The bar shown in Fig. 1 is subjected to a tensile load of 50 KN. Find the diameter of the middle portion if the 'stress is limited to 130 MN/m2, Find also the length of the middle portion if the total elongation of the bar is 0.15 mm. Take E=200 GN/m². 50 kN Fig. 1 40 mm dia. 250 mm 40 mm du. 50 KN

Q1/ The bar shown in Fig. 1 is subjected to a tensile load of 50 KN. Find the diameter of the middle portion if the 'stress is limited to 130 MN/m2, Find also the length of the middle portion if the total elongation of the bar is 0.15 mm. Take E=200 GN/m². 50 kN Fig. 1 40 mm dia. 250 mm 40 mm du. 50 KN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 1. P T The figure (not drawn to scale) shows a cylindrical column submitted to a combined load: a compression of and torsion. Given column diameter d = 29 mm, compressive load p = 110 kN, and torque T = 500 N.m, calculate the maximum shear stress Tuast and the Von Mises stress ov Enter your answers in the boxes below, correct to one decimal place. The answers are acceptable within a tolerance of 1 MPa. Tmax [ MPa MPa OVM:
Simple stressa nd strain problem! Pleasee help
Don't waste my question please, I need the solution don't just capy the answer that I give there.
4. The stepped circular bar shown below is made from aluminum (E = 70 GPa, v = 0.35). Each segment is 400 mm in length. Prior to applying the loads, the bar has the dimensions shown. The structure is axially loaded as shown. Determine the stress in each segment, the maximum stress and its location, the final in length of the structure, and the final diameters of each segment due to the applied loads. All dimensions shown are in mm. Ø 25 40 15 ↑ Fu 300 kN 600 kN 300 kN
Rod(1), rod (2) where 1, 2 rod numbers not the graded question
A member is formed by connecting two steel bars shown below. Assuming that the bars are prevented from buckling sideways, calculate the magnitude force "P" that will cause the total length of the member to decrease 0.24 mm the values of elastic modulus for steel is 221 MPa. Take H1 = 4 cm, H2 is 2 x 2 cm and bottom bar (Q) is 6 x 6 cm. Also, determine the stress-induced in each section of the bar. = 9 cm, top bar (R) IP Solution: R cm x RCm Steel bar i) Magnitude Force, P = H1 cm ii) Stress-induced in the top bar = Q cm x Q cm Steel bar H2 cm iii) Stress-induced in the bottom bar =
2 3.0 m 175 KN 2.5 m 200 KN (1) (2) 46 mm 175 kN 30 mm Problem 3 A compound axial member consists of steel (E=200 GPa) segment (1) and brass (E=120 GPa) segment (2). a) Compute the total deformation of the compound member for the loading shown (in mm). b) Sketch an internal normal force diagram c) Calculate the average axial stress in segment 2
strength of material MENG222 Please solve the problem step by step and make your line clear and don't forget to show me your step
Determine the maximum axial force that can be applied to the bar shown in Figure 3. The allowable stress is 100 MPa. The dimensions are: Hole diameter 20 mm. Thickness of bar: 6 mm D = 40 mm d%3D20mm Fillet radius, r = 4 mm 40mm 20 mm r 4 mm 20 mm Figure 3 P.
Calculate the maximum stress in a 25 mm thick perforated bar and show its location on the figure. 200 mm = 30 mm 5000 N 5000 N r= 15 mm
need help asap :<
A steel wire is 10m long supports a tensile load of 2000N. What is the diameter if the stress is 140 MPa & the total elongation is 5mm.E=200 GPa.