Questions ( time: 30 min)Answer the following two questions:Q1: Find the resultant and itsFi=300 Ndirection of the two concurrent30°forces shown in figure (1). Useparallelogram law.F2=600 NFigure (1)Q2: The force system, shownin figure (2), has a horizontalresultant (to the right) of (250Ib).Find values of (P) & (F).300 NFigure (2)

Hi there! since you have asked multiple questions, we will solve the first question for you. If you…

Answered: Q1: Find the resultant and its…

Engineering

Civil Engineering

Q1: Find the resultant and its direction of the two concurrent forces shown in figure (1). Use parallelogram law.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 6 A cantilever beam AC shown in Figure Q6 is subjected to uniformly distributed load w. (a) By use of the virtual work method, determine the rotation and deflection at the end A. Assume that El is constant and L is the length of AB and BC. (b) Describe the procedure to determine all reaction forces if the end A is simply supported in approximately 100 words (without actually solving the problem). A L L B Figure Q6 W L C
At the instant shown, the slider D has a velocity of 3 ft/s up the channel and its speed is decreasing at a rate of 0.5 ft/s². Determine at this instant: a. The angular accelerations a and acp (include magnitude and direction) b. The acceleration of point C in Cartesian form. Solve the problem using any method. 3.a a AB acD 3.b ac = = 10 in. 8 in. A B 12 in. D 30°
PLEASE REFER TO THE GIVEN VALUES BELOW. For the beam loaded as shown in the figure, determine the following unknowns using DOUBLE INTEGRATION METHOD. Consider 300 mm x 300 mm section and E = 200 GPa. Round-off to 3 decimal places. a = 3.3m b = 16 kN/m c = 16 kN - Determine reaction at A in kN. - Slope of the elastic curve at A in degrees. Indicate negative sign as necessary. - Deflection at B in mm. Indicate negative if downward. - Deflection at D in mm. Indicate negative if downward.
The continuous beam is loaded as shown in the figure. The supportsatA is fixed, B, D and C are rollers. Use Slope-Deflection in determining the following: a.Reaction at the given supports. b.Shear and moment diagramof the beam E =200 GPa and I=100x10^6 mm^4
For the forces acting on the beam shown in Figure 3.1f, determine the location of the equivalent resultant force with reference to point A in m. Given / = 2.4, P1 = 8, P2 = 8 and w = 2 %3D (Note: Prefix the answer with negative sign "." if the location is to the left of the reference point. E.g. if the location of the equivalent resultant is located between points A and B, or to the left of point B by 1.2m, the answer should be "-1.2" with reference to point B) P, kN W kN/m P, kN C 21 m 21 m Figure 3.1f
Determine the intenal normal force, shear force, and moment at point Cin the simply supported beam. Point Cis located just to the right of the 250 Nm couple moment. * Make sure to add units out of ** Your answer should look like this: Ne =, Vc=. Mc 100 N 5 m 300 N/m A 35 250 N.m 8 m 4 m 4 m 40 N Answer
Problem 3. Determine the following unknowns on the beam shown below using Conjugate-Beam Method. Consider 250 mm x 250 mm section and E = 200 GPa. Show complete and organized solution. Round-off your answers to two decimal places. a. Vertical Reaction at C in kN. a=4.5 b. Moment Reaction at C in kN-m. c. Deflection at point B in mm. d. Maximum deflection on the beam in mm b=30.0kN/m c=12KN c kN b kN/m A "a" m “a" m
Problem 3. Determine the following unknowns on the beam shown below using Conjugate-Beam Method. Consider 250 mm x 250 mm section and E = 200 GPa. Show complete and organized solution. Round-off your answers to two decimal places. a. Vertical Reaction at C in kN. b. Moment Reaction at C in kN-m. c. Deflection at point B in mm. d. Maximum deflection on the beam in mm
Determine the following unknowns on the beam shown below using Conjugate-Beam Method. Consider 250 mm x 250 mm section and E = 200 GPa. Show complete and organized solution. Round-off your answers to two decimal places. a. Vertical Reaction at C in kN. b. Moment Reaction at C in kN-m. c. Deflection at point B in mm. d. Maximum deflection on the beam in mm
A beam is subjected to a uniform force w as shown in the figure below. The E of the entire section is 200 GPa, and the I is 60×10^6 mm^4. Try to draw the beam’s Shear Curve and Moment Curve.(a) If point C supports sink 0.1 m before assembly(b) If the uniform force w is removed and the point C sinks, but the point A support is rotated 0.005 rad clockwise before assembly
The continuous beam shown in the figure is fixed at both ends A and D, and supported by rollers at B and C. Assume I 800 x 106 mm and E = 70,000 MPa. %3D W1 BO C 8m 8 m 4 m 4 m W1 (kN/m) F (kN) s (mm) 20 60 25 If there is a settlement of S at the support C, solve the following using slope deflection method: 3. Reaction at A, RA in kN. 4. Moment at A, MA in kN-m 5. Reaction at D, RD in kN 6. Moment at D, MD in kN-m
Problem 3. Determine the following unknowns on the beam shown below using Conjugate-Beam Method. Consider 250 mm x 250 mm section and E = 200 GPa. Show complete and organized solution. Round-off your answers to two decimal places. a. Vertical Reaction at C in kN. A. 4.2 m b. Moment Reaction at C in kN-m. c. Deflection at point B in mm. B. 22 kN/m d. Maximum deflection on the beam in mm C. 9 kN c kN b kN/m BI "a" m "a" m