Q1: Fill in the following blanks: .... layer. 1. The most superior material is used in ..... 2. The presence of moisture content causes. 3. The spacing of joint depends on .... 4. The maximum load safety factor in rigid pavements design assumed is is the least commonly used as a rigid pavement type. 5. (

Q1: Fill in the following blanks: .... layer. 1. The most superior material is used in ..... 2. The presence of moisture content causes. 3. The spacing of joint depends on .... 4. The maximum load safety factor in rigid pavements design assumed is is the least commonly used as a rigid pavement type. 5. (

Traffic and Highway Engineering

5th Edition

ISBN:9781305156241

Author:Garber, Nicholas J.

Publisher:Garber, Nicholas J.

Chapter20: Design Of Rigid Pavements

Section: Chapter Questions

Problem 7P

See similar textbooks

Similar questions

Give me right solution... Urgent please A 5 tonne wheel load is applied on a pavement and generates a surface deflection of 0.15 mm. A. If the pavement is 125 mm thick, what is the vertical stress at the top of the subgrade? B. If the equivalent radius of tyre contact is 100 mm and Poisson’s ratio is 0.3, what is the pavement’s modulus of elasticity
A concrete pavement is constructed at a temperature of 10°C. The peak summer temperature is 30°C. The coefficient of temperature is 10 x 10^- 6/°C. The gap at the expansion joint is 2.5 cm. The spacing of expansion joint is what.
Q3/Choose the correct answer 1. In general PSI for flexible pavement depend on............ Va. Cracking, Patching and Rutting b. Cracking and Patching c. Patching and Rutting d. Rutting 2. The Maximum contraction joint spacing for plain jointed concrete pavement is C. 3.5 m b. 4.5 m c. 5.5 m d. Depends on traffic load 3. The relationship between A psi and age of pavement is...... a. A psi co age Apsi ∞ (1/age) c. A psi 02(1/age) d. Non of the above 4. The surface of the pavement should be a. Smooth b. Rough 5. Which type of aggregates gives good workability? a. Round b. Flaky c. Angular 6. Rutting may be avoided by a. Good compaction . Sufficient enough to resist skid b. Good drainage 7. Bleeding may be avoided by a. Water voids b. Air voids c. Asphalt type 12. Tie bars in cement concrete pavements are at a. Expansion joints d. All the above acceptable c. High filler percent All the above 8. The good drainage in pavement can La Increase the pavement life b. Decrease the pavement life…
Determine the thickness of a rigid pavement with a wheel load capacity of 54 kN, if the allowable tensile stress of the concrete is 1.6 MPa. Neglect the effect of dowels.
5. A rigid pavement is to be used to carry a wheel load of 54.04 kN. Enough dowels will be used across the joint. What will be the difference in thickness (in mm) between the edge and the center of the pavement? The allowable tensile strength of concrete is 1.42 MPa. Round off to the nearest whole number.
A pavement element along Thika road of 100x150x200 mm was subjected to an equalall round pressure of 120kn/m2 and axial load of 2.5KN in the X-direction. The changesin length are 0.92mm in X-direction, 0.27mm in the Y-direction and 0.18mm in the Z direction. Calculate thei. Elastic theory ratio, Eii. Poisson’s ratio,iii. Bulk Modulus, K
A rigid pavement is to be used to carry a wheel load of 58.77 kN. Enough dowels will be used across the joint. The allowable tensile strength of concrete is 1.45 MPa. Thus, what will be the difference in thickness (in mm) between the edge and the center of the pavement?
A rigid pavement is to be used to carry a wheel load of 50.93 kN. Enough dowels will be used across the joint. What will be the difference in thickness (in mm) between the edge and the center of the pavement? The allowable tensile strength of concrete is 1.39 MPa.
A concrete pavement is subject to a temperature change of AT = 70°F; a coefficient of thermal expansion a = 5.5 ×10 in./in./°F; a concrete shrinkage ɛ = 200 x106; and a granular base with C = 0.8. Determine the joint spacing for an undoweled and a doweled joint having an allowable joint opening of 0.06 and 0.02 in., respectively.
Calculate the design thickness in mm (rounded to the nearest tens) at the edges of a rigid pavement with dowels if the: Allowable tensile strength of concrete = 3.1 MPa Wheel load = 120 kN 240 250 C 280 300
show that the design thickness of a concrete Pavement slab is safe for Combined load and temperature stresses for longitudinal and conditions, given fellowling data: Design thickness = 20 Con Maximum wheel load = 4080 kg ● Impact factor - 10% . . modules of elesticity of concrete = 3x 100 kg/cm² modulus of Subgrade reaction = 6kg/cm³. Paisson's ration of Concreate = 0.2 ● • Type Slab pressure = 7 Kg/cm2 dimensions = 4.5m x 3.8m • Thermal conefficient of concrete = 8x10° per °C • Temperatore difference during the day = 0+5°C/cm Allowable flexural Strength of concrete=3skg/ ● Com 2
17. In the Asphalt Institute flexible pavement design approach, Where are the critical stress and strain locations checked?a. Top of the asphalt concrete layerb. Middle of the asphalt concrete layerc. Bottom of the asphalt concrete layerd. Bottom of the asphalt concrete layer and top of the subgrade