Q1- Attempt only five of the following: 1- IF AX=-2000 and BL= 5, when IDIV BL get executed an error occur, fix t error then justify your answer in proper comment. 2- How many bytes are following? i- The Interrupt Service Routine (ISR) address ii-The Interrupt Vector Table (IVT) 3-For INT 1Ch, Show the IP and CS of the ISR that could be existed.

Q1- Attempt only five of the following: 1- IF AX=-2000 and BL= 5, when IDIV BL get executed an error occur, fix t error then justify your answer in proper comment. 2- How many bytes are following? i- The Interrupt Service Routine (ISR) address ii-The Interrupt Vector Table (IVT) 3-For INT 1Ch, Show the IP and CS of the ISR that could be existed.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

If (BHE'=0, M/IO'=0, Address lines include an odd address, WR'=O, RD'=1), it means: * Transmitting 8-bit data from 8086Mp to memory. Transmitting 8-bit data from an I/O device to 8086Mp. Transmitting 16-bit data from an I/O device to the 8086Mp. Transmitting 16-bit data from memory to the 8086Mp. Transmitting 16-bit data from 8086Mp to memory. Transmitting 8-bit data from memory device to 8086Mp. Transmitting 8-bit data from 8086Mp to an 1/0 device. Transmitting 16-bit data from 8086Mp to an 1/0 device.
Which of the following statements is correct? I. The 80/20 rule states that 80% of instructions are executed and 20% are created. External bus is used exclusively for data memory in von Neumann architecture II. a) Only I is true; b) Only II is true; c)Both I and I are true; d) Neither I nor |l is true.
2- Write an assembly language program to test the contents of 5 memory locations start at (2000) if thelr parlty Is odd reset that locatlon otherwise store FF In that locatlon. 3-A block of 18 signed numbers stored at memory locations starting at DS:300. Write an assembly language program to transfer the positive numbers to a new memory locations starting at DS:500, and the negative numbers to memory locations starting at DS:400
QUESTION 10 Write the execute cycle of LOAD 1020 that load the value from memory address 1020 in Register Transfer Notation; show micro-operation. TTT Arial 3 (12pt) 三, Path: p Words:0 Click Save and Submit to save and submit. Click Save All Answers to save all answers. Save All Answers !!!
Consider the below interrupts and their priority settings of user and natural interrupt priorities. a. Ext_interrupt_1: User Priority = 1, Interrupt Vector = 30; b. Ext_interrupt_2: User Priority = 0, Interrupt Vector = 45; c. Ext_interrupt_3: User Priority = 1, Interrupt Vector = 90; d. Ext_interrupt_4: User Priority = 1, Interrupt Vector = 95; If the above interrupts occur at the same time, which one will be served first? a b.
* The LOOP # will affect only CX O only IP All CS, CX and IP Both CX and IP non of those It can implement the complement of the interrupt flag directly True O False
Que 4.13. Develop an assembly language programme for 8086. are stored from 9300 to 930F and 9400 to 940F. The result is to be stored add two binary numbers each of 16 byte long. The numbers from 9300 to S930F.
Q:Answer the following sentence with (True) or (False) and correct the false answer: 1. You can input data of size 16-bit through the fixed port. 2. In the maximum mode, the status signals S₁, S₂ and S3 are controlled by the bus controller. 3. HLDA is an output signal. 4. In 8086, when executing the instruction MOV AL, [SI+100D H] where SI-100AH, Ao=0 and BHE=1 5. When S, is 0, the TF is disabled.
What is the 32-bit value at address 0x7FF4? What is the 16-bit value at address 0x7FFA? what is the 32-bit value at address 0x7FFC? What is the 16-bit value at address 0x7FF6? What is the 16-bit value at address 0x7FF2?
There are three condition code flags in the Y86-64 that are set by arithmetic and logical operations. The flags are then used by the conditional jump and conditional move instructions as follows. • ZF-Zero Flag: The previous operation left a value of zero. • SF - Sign Flag: The previous operation left the most significant bit of the operand 1. • CF - Carry Flag: The previous operation resulted in an overflow. Suppose we pass the following values to sum (): array 13, -17, 2: len 3 What are the condition codes when sum () returns? ZF: CF: SF: Match the value 0 or 1 to the three condition codes below. Separate each value with a comma. ► View Available Hint(s) ZF, CF, SF Submit