Q1: An oil of S= 0. 8 is flowing through a venture meter having a (200- (0.5*your code number)) mm and the diameter of the throat is 100 mm. The mercury differential manometer shows a reading of (250+(0.5*your code number))mm. If the flow rate of oil through the horizontal venture is 70.5 liter/s. Calculate the coefficient of discharge ( Cd):- diameter of code numberz 28.9

Q1: An oil of S= 0. 8 is flowing through a venture meter having a (200- (0.5your code number)) mm and the diameter of the throat is 100 mm. The mercury differential manometer shows a reading of (250+(0.5your code number))mm. If the flow rate of oil through the horizontal venture is 70.5 liter/s. Calculate the coefficient of discharge ( Cd):- diameter of code numberz 28.9

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please solve using MLT system. F=MLT^(-2) (Hand written and neat and clean answer )
Water Gs=1 1. In a test to determine the discharge coefficient of a 70 by 35 mm Venturi meter, the total weight of water passing through the meter in 3 minutes was 3.5 kN. A mercury differential gage connected to the inlet and throat of the meter showed an average mercury difference during that time of 300 mm.. Determine the actual discharge if the same meter is used later on and a 250 mm difference is then observed. h = 300 mm Mercury, Hg Gs = assume, 4 significant figures 0
I need an answer asap. Need it in 10 mins thank you
Fluid 9
help asap fill out table
Heavy oil discharges from a pipe through a sharp-crested, 100-mm-diameter orifice having discharge coefficient of 0.63. (a) What is the coefficient of velocity? (b) What is the velocity (m/s) of oil jet? (c) What is the head loss (m) through the orifice? 250 Orifice 1 Pipe OIL (SG = 0.91) MERCURY (SG = 13.6) NOTE: easurements are in 'mm' 350
Express your solution in 4 decimal places.
2. A large-capacity faucet is to be connected to a water main by 20-mm diameter copper tubing as shown in Figure below. The copper tubing has an estimated f=0.02, and local head losses are created by the corporation stop (C-stop), three bends, and the faucet itself. The faucet exit has a diameter of 12 mm. What is minimum pressure in the water main required to obtain a desired flow rate of 50 L/min when the faucet is fully open? fig1.Faucet connected to water main. Water main Bend 3.5 m C-stop E 2 5m Pipe Bend Bend E Bend 4 m Faucet Fitting C-stop Bend(s) Faucet K 9 1.2 10
Whiskey (SG = 0.6 and ν = 5.0 x 10-7 m2/s) is drawn from a large tank through a smoothed, rubber hose as shown in the figure. The total length of the hose to be used is 9 m and the length of the hose to point A is 3.25 m. The intended extraction of whiskey is 10 L/s and minor losses at the entrance are to be neglected. a) Calculate the smallest diameter (in 5 mm interval) required to achieve therequired flow using an iterative solution. Use an initial value of the friction factor, f0 = 0.020.b) Is the equation derived by Swamee and Jain applicable to solve the requireddiameter? Explain.c) Calculate the smallest gage pressure in the hose using the diameter (in 5 mminterval) solved.
A pipe has an outer diameter of 26 mm and an inner diameter of 19 mm. What is the polar moment of inertia "J" for the shaft in mm^4? Type your answer...
A closed tank is filled with oil and water with the given situation as shown in the figure. An orifice with an unknown diameter is placed 1 m from the bottom of the tank discharging 10 L/s based on a calibration test. The jet from the orifice hits the ground 3.8 m horizontally away from the vena contracta. If the coefficient of discharge is 0.64, determine: a. The diameter of the orifice b. The coefficient of cotraction. Air p- 16 KPa 1 m S0.82 3.80 m Water 1m 2 m 1m
Find the discharge in pipe 5 in L/s using the Hardy Cross method. (Use AQ<1 L/s as a threshold in your solution) If the discharge occurs in the counterclockwise direction, use a negative sign. 100 L/s K=1 Pipe 1 K=2 K=3 Pipe 3 Pipe 2 Pipe 4 K=2 Pipe S K=1 25 L/s 75 L/s h iPhone