Q1: A space 16 mm wide between two large plane surface is filled with SEA 30 lubricating oil (0.18 N/m²) as shown in figure (1) What force F is required to drag a very thin plate of 0.4 m² area between the surfaces at a speed of 0.25 ms. a. If this plate is equally spaced between the two surfaces. b. Ift-5mm.

Q1: A space 16 mm wide between two large plane surface is filled with SEA 30 lubricating oil (0.18 N/m²) as shown in figure (1) What force F is required to drag a very thin plate of 0.4 m² area between the surfaces at a speed of 0.25 ms. a. If this plate is equally spaced between the two surfaces. b. Ift-5mm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q3: The space between two large flat and parallel walls 25 mm apart is filled with a liquid of absolute viscosity 0.7 Pa.sec. Within this space a thin flat plate 25 cm x 25 cm is towed at a velocity of 0.15 m/s at a distance of 6 mm from one wall, the plate and its movement being parallel to the walls. Determine the force exertem by the liquid on the plate. Stationary plate 6 mm 19 mm 0.15 m/s Stationary plate
26. A block with a mass m is placed on the top of an identical block m and the system of two blocks is at rest on a rough horizontal surface as shown below. The top block is tied to the wall. The coefficient of static friction between all surfaces is us. What maximum value does force F reach before the lower block starts sliding to the left? * F m e. 4 psmg c. 4 usmg d. ½ psmg a. 3 psmg O b. 2 psmg
Civil Eng FLUID MECHANICS Que. 104 Find the minimum value of friction factor than can occur in laminar flow through a circular pipe.
The W1= 57.94-lb block shown rests on a smooth plane (coefficient of kinetic friction = 0) with an angle of θ=25∘ from horizontal. It is connected by a flexible inextensible cord that passes around weightless, frictionless pulleys to a support. The W2 =112.33-lb weight is attached as shown. After the system is released from rest, in what distance will the block on the plain attain a speed of 7.0 ft/s?
Q3 The space between two square flat parallel plates is filled with oil . Each side of the plate is 720 mm . The thickness of the oil film is 15 mm . The upper plate , which moves at 3 m / s requires a force of 120 N to maintain the speed . Determine : ( 1 ) The dynamic viscosity of the oil ; ( ii ) The kinematic viscosity of oil if the specific gravity of oil is 0.95 .
Situation 22: The 125-kg concrete block A is released from rest in the position shown and pulls the 200 kg log up the 30" ramp. If the coefficient of kinetic friction between the log and the ramp is 0.5, compute the following: Sit kp rac fri ca Si 200 kg u HA3D0.5 T 125 kg 6m 30° 1 2 1. acceleration of block A as it hits the ground 2. tension in the cable supporting block A 3. velocity when block A hits the ground
The figure shows a two - dimensional jet divid ed by a wedge O Assume the velocity at Icle 2. De rermine the Force exer ted by the jet. 8 = 9,81 KN/" = 9.81 horizontal Az=0 13ch V= 3 m/s -> of 20cm P=185.3 Ku/mて 2 V, = ?? V2 = ?? F-x direction =?? -クク F- Y direction = 13k-
Q3 The space between two square flat parallel plates is filled with oil. Each side of the plate is 720 mm. The thickness of the oil film is 15 mm. The upper plate, which moves at 3 m/s requires a force of 120 N to maintain the speed. Determine: (i) The dynamic viscosity of the oil; (ii) The kinematic viscosity of oil if the specific gravity of oil is 0.95.
Example 700 mm An experimental device imparts a force of magni- tude F = 225 N to the front edge of the rim at A w 900 mm simulate the effect of a slam dunk. Determine the moments of the force F about point O and about point B. Finally, locate, from the base at 0, a point C on the ground where the force imparts zero moment. B 300 mm A 3050 mm
The 8 mm gap between two large vertical parallel plane surfaces is filled with a liquid of viscosity 2x10-2 Ns/m². A thin sheet of 1 mm thickness and 150 mm x 150 mm size, when dropped vertically between the two plates attains a steady velocity of 4 m/s. Which nearly gives the weight of the plate in Newton. Assume that the plate moves centrally. O a. 0.87 O b. 1.25 O c. 2.10 O d. 1.03
The space between two square flat parallel plates is filled with oil. Each side of me plate is 720 mm. The thickness of the oil film is 15 mm. The upper plate, which moves at 3 m/s requires a force of 120 N to maintain the speed. Determine: () The dynamic viscosity of the oil;
6. A flat plate 200 mm x 750 mm slides on oil (μ = 0.85 Pa.s) over a large plane surface as shown in the figure. What force F is required to drag the plate at a velocity v of 1.2 m/s if the thickness t of the separating oil film is 0.6 mm. a. 170 N b. 1700 N c. 255 N Oil d. 2.5 Plate -F. V