Q1) A simply supported beam having a length of 7 meters carries a uniformly distributed load of 16KN/m over its entire length and has the cross-sectional area shown in the figure with IN.A=8.723 10“m*. Find T to cause a maximum bending stress of 80MPA and a maximum shearing stress of 40MPA? -100mm- 20mm -20 80mm 68.3mm 20

Q1) A simply supported beam having a length of 7 meters carries a uniformly distributed load of 16KN/m over its entire length and has the cross-sectional area shown in the figure with IN.A=8.723 10“m*. Find T to cause a maximum bending stress of 80MPA and a maximum shearing stress of 40MPA? -100mm- 20mm -20 80mm 68.3mm 20

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter10: Statically Indeterminate Beams

Section: Chapter Questions

Problem 10.4.32P: Two identical, simply supported beams AB and CD are placed so that they cross each other at their...

See similar textbooks

Similar questions

A beam supporting a uniform load of intensity q throughout its length rests on pistons at points A, C and B (sec figure). The cylinders are filled with oil and are connected by a tube so that the oil pressure on each piston is the same. The pistons at A and B have diameter d1and the piston at C has diameter D2. (a) Determine the ratio of d2to d1so that the largest bending moment in the beam is as small as possible. Under these optimum conditions, what is the largest bending moment Mmaxin the beam? What is the difference in elevation between point C and the end supports?
The Z-section of Example D-7 is subjected to M = 5 kN · m, as shown. Determine the orientation of the neutral axis and calculate the maximum tensile stress c1and maximum compressive stress ocin the beam. Use the following numerical data: height; = 200 mm, width ft = 90 mm, constant thickness a = 15 mm, and B = 19.2e. Use = 32.6 × 106 mm4 and I2= 2.4 × 10e mm4 from Example D-7
Derive the following formula for the distance e from the centerline of the wall to the shear center S for the hat section of constant thickness shown in the figure: Also, check the formula for the special case of a channel section (a = 0).
Determine the maximum tensile stress (7, (due to pure bending about a horizontal axis through C by positive bending moments (B) for beams having cross sections as follows (see figure). A semicircle of diameter d. An isosceles trapezoid with bases (b) = b and f2 = 4W3 and altitude h. A circular sector with a = ît/3 and r = d/2.
The cross section of a composite beam made of aluminum and steel is shown in the figure. The moduli of elasticity are TA= 75 GPa and Es= 200 GPa. Under the action of a bending moment that produces a maximum stress of 50 M Pa in the aluminum, what is the maximum stress xs in the steel? If the height of the beam remains at 120 mm and allowable stresses in steel and aluminum are defined as 94 M Pa and 40 M Pa, respectively, what heights h and h. arc required for aluminum and steel, respectively, so that both steel and aluminum reach their allowable stress values under the maximum moment?
The cross section of a sand wie h beam consisting of aluminum alloy faces and a foam core is shown in the figure. The width b of the beam is 8.0 in, the thickness I of the faces is 0.25 in., and the height hcof the core is 5.5 in. (total height h = 6.0 in). The moduli of elasticity are 10.5 × 106 psi for the aluminum faces and 12.000 psi for the foam core. A bending moment M = 40 kip-in. acts about the z axis. Determine the maximum stresses in the faces and the core using (a) the general theory for composite beams and (b) the approximate theory for sandwich beams.
A small dam of a height h = 6 ft is constructed of vertical wood beams AB, as shown in the figure. The wood beams, which have a thickness I = 2.5 in., are simply supported by horizontal steel beams at A and Ä Construct a graph showing the maximum bending stress tram in the wood beams versus the depth d of the water above the lower support at B. Plot the stress0mas(psi) as the ordinate and the depth d(ft) as the abscissa. Note: The weight density y of water equals 62.4 lb/ft3.
A simple beam A B of a span length L = 24 ft is subjected to two wheel loads acting at a distance d = 5 ft apart (see figure). Each wheel transmits a load P = 3.0 kips, and the carriage may occupy any position on the beam. Determine the maximum bending stress Gmaxdue to the wheel loads if the beam is an I-beam having section modulus S = 16.2 in3. If d = 5 ft. Find the required span length L to reduce the maximum stress in part (a) to 18 ksi. If L = 24 ft, Find the required wheel spacing s to reduce the maximum stress in part (a) to 18 ksi.
A hollow steel box beam has the rectangular cross section shown in the figure. Determine the maximum allowable shear force K that may act on the beam if the allowable shear stress is 36 MPa. c
The cross section of a rectangular beam having a width b and height h is shown in part a of the figure. For reasons unknown to the beam designer, it is planned to add structural projections of width b/9 and height d/9 the top and bottom of the beam (see part b of the figure). For what values of d is the bending-moment capacity of the beam increased? For what values is it decreased?
A tapered cantilever beam A B of length L has square cross sections and supports a concentrated load P at the free end (sec figure part a). The width and height of the beam vary linearly from kAat the free end to hBat the fixed end. Determine the distance.y from the free end A to the cross section of maximum bending stress if hE= 3h4, What is the magnitude ffœai of the maximum bending stress? What is the ratio of the maximum stress to the largest stress B at the support? Repeat part (a) if load P is now applied as a uniform load of intensity q = P/L over the entire beam, A is restrained by a roller support, and B is a sliding support (see figure part b).
A beam of wide-flange shape, W 8 x 28, has the cross section shown in the figure. The dimensions are b = 6.54 in., h = 8.06 in., fw = 0.285 in., and tf = 0.465 in.. The loads on the beam produce a shear force V = 7.5 kips at the cross section under consideration. Use center line dimensions to calculate the maximum shear stress raiaxin the web of the beam. Use the more exact analysis of Section 5,10 in Chapter 5 to calculate the maximum shear stress in the web of the beam and compare it with the stress obtained in part .