Q1 /A plant has the open loop transfer function shown below, with unity negative feedback and step input with 5 final value . G(s) = s+1)(s – 4) (s+2)(s+3)* Build a Simulink model to generate the plant closed loop transfer function. Set the Stop Time as 30sec. plot the step response of the closed loop system. also generate a plot of the closed loop system with sinusoidal input of amplitude 15, Frequency 0.2Hz.

Q1 /A plant has the open loop transfer function shown below, with unity negative feedback and step input with 5 final value . G(s) = s+1)(s – 4) (s+2)(s+3)* Build a Simulink model to generate the plant closed loop transfer function. Set the Stop Time as 30sec. plot the step response of the closed loop system. also generate a plot of the closed loop system with sinusoidal input of amplitude 15, Frequency 0.2Hz.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q- 2: Suppose you are designing a Mathematical Calculator. You need Logarithmic and Anti logarithmic functions for the calculator. Draw a neat circuit diagram of an Op Amp based log Amplifier. Derive the output voltage expression for the above circuit justifying its name. Draw a neat circuit diagram of an Op Amp based Anti-Log Amplifier.
Q– 2: Suppose you are designing a Mathematical Calculator. You need Logarithmic and Anti logarithmic functions for the calculator. Draw a neat circuit diagram of an Op Amp based log Amplifier. Derive the output voltage expression for the above circuit justifying its name. Draw a neat circuit diagram of an Op Amp based Anti-Log Amplifier. CS Scanned with CamScanner
The OP AMP circuit in below figure has a capacitor in its feedback loop. Determine the circuit gain (a) at dc and (b) as the frequency approaches o rad/s. C R R + vo(t) Vs(1) +
Determine the state equations and op equation fa - The system belon), - 2
Design a circuit to amplify and filter a signal with a bandwidth from dc to 300 Hz and that varies from -100 μV to 100 μV. The output signal should have a peak-to-peak amplitude of 5 V. Include all component values and op amp part numbers in your design.
please replicate this schematic diagram in TinkerCad. please do leave some notes to better understand the circuit also can you define the circled component? If you are unfamiliar with the software a sketch of a breadboard showing how the components, specially the op-amp, would suffice. [Take note that R2 is a LDR and the output of the circuit is connected to apiezo. The input is a sinusoidal voltage with amplitude 0.2V, 0V DC offset,and a frequency of 2000 Hz.]
I want the answer with details as soon as possible. Please Q-Design an op-amp circuit to amplify the AC voltage of 0.7v to become 3v , And the voltage of VCC is 5v DC.
Find rise time, peak time, maximum overshoot, and settling time in the unit-step response of a closed-loop system described by the following closed-loop transfer function:
A unity feedback system has the open loop transfer function shown below. Find the breakin point. Your answer must be in decimal form to two decimal places. HG(s)=- K(s - 3)(s-5) (s + 1)(s+2)
: It is known that the lower cutoff frequency value is 63.66 Hz and the bandwidth value is 381.97 Hz in the circuit with Op-Amp in the figure. According to the element values and connection information given in the circuit, R1=?
Find the output for the system represented by transfer function shown in figure (2-10) analytically and compare with the simulated result. (Assuming all initial conditions is zero)
Disadvantages of Inverting and Non-inverting Op Amp p 12:59