Q#01: Write a short note on What are the best possible solutions to increase the heat transfer rate of a body.Which material will transfer more heat? Either a material with thermal conductivity ? = 121 or ? = 22 . Justify your answer. Explain the Fouling phenomenon. What is the effect of fouling on heat transfer rate?

Q#01: Write a short note on What are the best possible solutions to increase the heat transfer rate of a body.Which material will transfer more heat? Either a material with thermal conductivity ? = 121 or ? = 22 . Justify your answer. Explain the Fouling phenomenon. What is the effect of fouling on heat transfer rate?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.24P

See similar textbooks

Similar questions

Q#01: Write a short note on the following: What are the best possible solutions to increase the heat transfer rate of a body? Which material will transfer more heat? Either a material with thermal conductivity ? = 121 or ? = 22 . Justify your answer. Explain the Fouling phenomenon. What is the effect of fouling on heat transfer rate.
Q#01: Write a short note on the following: What are the best possible solutions to increase the heat transfer rate of a body? Which material will transfer more heat? Either a material with thermal conductivity ? = 121 or ? = 22 . Justify your answer.
What will be the rise in temperature in 30 minutes of a block of copper of 500-gram mass if it is joined to a cylindrical copper rod 20 cm long and 3.0 mm in diameter when a temperature difference of 80 degree Celsius is maintained between ends of the rod? The thermal conductivity of copper is 1.02 cal/cm2-sec-°C/cm (neglect heat losses). Please include FBD
3. The heat flux (from outside to inside) across an insulating wall with thermal conductivity, K= 0.04 W/m-K and thickness 0.16m is 10 W/m2. The temperature of the inside wall is - 5°C. The outside wall temperature is _____. (avoid rounding off during intermediate steps, but only on final answers to four decimal places.)
%^0 |. دردشة هندسة النفط/مسائي A composite wall consisting of five series layers of materials with different properties. Layer thickness, thermal conductivity of the layers and temperatures are shown on the figure. Based on Fourier's law for conduction, answer the following questions. 1. What are the main assumptions? 2. Drive an equation to calculate the heat transfer rate through the Composite wall? 3. Draw the themal circuit through composite wall? 4. What are the value Ti? 5. What are the value Tj? 6. What are the value Tr? Givens: KA = 2 W/m. °C K= 1 W/m.°C K= 5 W/m. °C Kp= 4 W/m, °C 100°C Ti 25°C Tj Tr A B D -2cm e 6 cm 4 cm 4cm إضافة وصف...
Determine the heat conduction of a boiler if you are given the following data: The thickness of the boiler is 15 cm, the T1 is the temperature of the water is 25°C and the T2 of the steam is 110°C, the thermal conductivity The boiler material is iron (use presentation table), the boiler area is 4.5 m^2
A pipe carries hot molten lead from one part of a factory floor to another. The mass flow rate of lead is 0.05 kg/s. While trying to figure out the heat loss from the pipe, you found that over a 2-m length of he pipe the lead temperature drops from 580 C to 557.C. What is the rate at which thermal energy is being lost from the lead carrying pipe in this 2-m section? Use the property table to find out properties of lead as needed.
Question 1 A copper tube that experience a temperature change is placed between two rigid caps. Four steel bolts are symmetrically arranged parallel to the axis of the tube and are lightly fastened. The copper has a cross-sectional area, length, Young's modulus and coefficient of expansion of 2000 mm², 300 mm, 100 GPa and 16 x 10-6 /°C respectively. The steel has a diameter, Young's modulus and coefficient of expansi on of 22 mm, 200 GPa and 12 x 10-6/°C respectively. Find the stress in the tube if the temperature of the assembly is raised by 70°C 1.1 1.2 What load will each bolt carry at the raised temperature
Consider the following cases: Case 1: A rod with specified surface temperature. Case 2: A rod with specified surface temperature with heat generation. Case 3: A rod with specified surface temperature with variable thermal conductivity k=k(1+ßT), ß: is constant. The quadratic temperature profile T(r)= f(r ) will be in: Select one: A. Case (1) and Case (2) ONLY B. Case (1), Case (2) and Case (3) C. Case (1) ONLY D. Case (2) ONLY E. Case (3) ONLY F. Case (1) and Case (3) ONLY G. Case (2) and Case (3) ONLY
Briefly explain the following. 1.The effect of cross-sectional area and thermal conductivity on conduction mode of heat transfer. 2=Temperature Profile. 3=Thermal conductor. 4=Why the temperature of heat conduction study bench should not exceed 70°C.
A boiler furnace wall must have a heat loss no greater than 700 Btu/hr~ft2 and is madeof a material with a thermal conductivity of 0.60 Btu/hr~ft~F. The inner wall surfacetemperature is '2000°F, and the outer surface temperature is 800°F. What wall thick~ness is required?
Question 1 A copper tube that experience a temperature change is placed between two rigid caps. Four steel bolts are symmetrically arranged parallel to the axis of the tube and are lightly fastened. The copper has a cross-sectional area, length, Young's modulus and coefficient of expansion of 2000 mm², 300 mm, 100 GPa and 16 × 10-6/°C respectively. The steel has a diameter, Young's modulus and coefficient of expansi on of 22 mm, 200 GPa and 12 x 10-6/°C respectively. 1.1 Find the stress in the tube if the temperature of the assembly is raised by 70°C