Q.4) A basketball player weighing 200 lb hangs on the rim of the basketball hoop shown below. The vertical post ABCD is fixed at support D and weighs 100 lb with its center of gravity at point C. The backboard hoop assembly weighs 60 lb with its and its center of gravity is located at point G. Determine the support reactions at D and forces acting at pins E and F. Neglect the weights of members AE, IF, and IJ. E 0.4 ft

Q.4) A basketball player weighing 200 lb hangs on the rim of the basketball hoop shown below. The vertical post ABCD is fixed at support D and weighs 100 lb with its center of gravity at point C. The backboard hoop assembly weighs 60 lb with its and its center of gravity is located at point G. Determine the support reactions at D and forces acting at pins E and F. Neglect the weights of members AE, IF, and IJ. E 0.4 ft

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A basketball player weighing 200 lb hangs on the rim of the basketball hoop shown below. The vertical post ABCD is fixed at support D and weighs 100 lb with its center of gravity at point C. The backboard hoop assembly weighs 60 lb with its and its center of gravity is located at point G. Determine the support reactions at D and forces acting at pins E and F. Neglect the weights of members AE, IF, and IJ.
Determine the forces in members DE, CE and BC in the Truss Shown.
Help
R2
Determine the force in the hydraulic cylinder EF that would maintain the parallelogram mechanism in the position shown.
A luggage trasport truck is used to raise and lower luggage from an aircraft. A piece of laggage weighing 450 Ibs. is supported in the tension shown with a center of gravity at point G. The raising and lowering mechanism are connected to the truck bed by a pin support at F and a roller support at H, and to the luggage platform by a pin support at C and roller support at D. The hydraulic strut AB is pinned at either end and used to raise and lower the mechanism are negligible, that point C is vertically aligned with F, point D is vertically aligned with H, and that strut AB is vertically oriented. (a) Determine the support Reaction at F and H in the stationary position shown. (b) Determine the force in the hydraulic strut AB and state weather it is in tension or compression. Please draw separate diagram for every step.
A rear suspension system for a front wheel-drive vehicle is shown here. Spring EF is offset behind member CD. The normal force due to contact between 2 wheel and the road is 4200 N. Assume the weight of the wheel and suspension system components is negligible. (a) Determine the magnitude of the force in member CD. Is the member in tension or compression? (b) Determine the support reactions at A. (c) Determine the unstretched length of the spring EF given a spring constant of 150 kN/m. 60 mm 1130 mm 60 mm 245 mm D 220 mm F 260 mm E B 165 mm 90 mm F = 4200 N
The level of a common steelyard without hook connections weights 7kg and acts at 5cm to the left of the fulcrum. The hook which carries the load,weights 4kg and is also attached on the left-hand side of the fulcrum at a distance of 12cm.if graduation mark 72cm from the fulcrum reads 50kg. Find (a).the weight of rider (b). How far is the zero graduation from fulcrum (c).What is the movement of riderper kg of graduation?
use sum of forces vertical and sum of forces horizontal
Three smooth cylinders, each weighing 500 N, is placed inside a smooth box as shown in the figure. B 3.1 Compute the reaction at A.
A rear suspension system for a front wheel-drive vehicle is shown here. Spring EF is offset behind member CD. The normal force due to contact between the wheel and the road is 4200 N. Assume the weight of the wheel and suspension system components is negligible. (a) Determine the magnitude of the force in member CD. Is the member in tension or compression? (b) Determine the support reactions at A. (c) Determine the unstretched length of the spring EF given a spring constant of 150 kN/m. 130 mm 60 mm 245 mm 60 mm D A 220 mm F 260 mm C EB 165 mm 90 mm * F = 4200 N
One of the smooth vertical walls supporting end B of the 230-kg uniform shaft is turned through a 21° angle as shown here. End A is supported by the ball-and-socket connection in the horizontal x-y plane. Calculate the magnitudes of the forces P and R exerted on the ball end B of the shaft by the vertical walls C and D, respectively. Assume a = 5.6 m, b = 2.3 m, L = 6.5 m, and 0 = 21° Answers: P = 2245 R = H. B a L D N A !N b