Q.11. A solid steel shaft has to transmit 75 kW at 200 rpm. Tak stress as 70 MN/m2. Find suitable diameter for the shaft, i transmitted on each revolution exceeds the mean by 30%.

Q: A solid steel shaft 4 m long is stressed to 91 MPa when twisted through 3 degrees. Using G = 84 GPa,…

A:

Q: Determine the magnitude of the reaction at pin A, pin B, pin C on CB

A: Determine the magnitude of reaction at A, B and C.

Q: The A-36 solid steel shaft is 2 m long and has a diameter of 67mm. It is required to transmit 69kW…

A: The given data is shown below: A-36 steelLength=2mDiameter=67mmPower=69 kWAllowable shear stress=80…

Q: Find the Sarce. narmal

A:

Q: A solid steel shaft 4 m long is stressed to 85 MPa when twisted through 4.4°. a. Given that G = 83…

A:

Q: A hollow steel propeller shaft, 20 ft. long with 15 in outer diameter and 12 in. inner diameter,…

A:

Q: Contact of a train wheel to the rail; It is realized at 10 kp / cm2 pressure, 3 cm width and 8 cm…

A: Given data, Pressure = 10 kip/cm^2 Width = 3 cm Length = 8 cm

Q: 7.) A steel tape of a nominal length of 30 m was used to check the distance between two offset pegs…

A: L = 30 mA = 2 mm2 W = 4.5 NE =  200 KN/mm2 or 200,000 N/mm2

Q: The observed temperature when the length of tape is 50 m is 29.6 °C and a pull of 15 kilos IS…

A:

Q: 8 A solid shaft has 100 mm diameter. It is used to transmits 120 watt power at 200 rpm (Take G = 8 x…

A: d=100mm N=200rpm P=120π To find maximum intensity of shear stress induced

Q: An aluminum tube of length 09.9(m) is used as column (fixed at both ends) carrying an axial load of…

A: Given: The length of the tube is 9.9 m. The axial load is 1319.67 N. The outer diameter of the tube…

Q: 85. A shaft turns at 200 rpm under a torque of 1800 Nm. The power transmitted is

A:

Q: 24 KN / m B 12 m 200 KN 6 m A D 10 m

A:

Q: Problem (1): Determine the internal torque in shaft (3) 50 N-m 28 N-m 21 N-m 14 N-m (4) E B…

A: When the load is acting on the body or specimen there is some deformation or change in the dimension…

Q: H.WOA vod Con sists of three bars af unequat dlameters as shown in fig. find the Stress in each bar…

A:

Q: A flat foot step bearing of 300 mm diameter supports a load of 8000 N. If the coefficient of friction…

A:

Q: 712 *5-44 The propellers of a ship are connected to a solid A-36 steel shaft that is 60 m long and…

A: StressExplanation:Step 1:Step 2:Step 3:Step 4:

Q: Derive a formula for the pressure difference Pa - P in terms of the system parameters in the figure…

A:

Q: Ex A bar ans: A13 X= 2-2 M The Smooth hari Zantel position planes in Find the distance X, as 1 kW…

A: Bar AB resting on two horizontal planes

Q: A load P=5 KN is supported by two concentric springs arranged as shown in figure below. The inner…

A: Load supported by two concentric springs = 5 kNNumber of turns in inner spring, n1 = 30…

Q: A motor transmitting 60 kW at 600 rpm drives a solid steel shaft ABC with a diameter of 50 mm. The…

A:

Q: Solve for the support reaction of the following problem. kindly show your solutions below. thank you

A:

Q: 3 praw A m the influence E 't 2 FOT B + line of moment at point D 1. S + 0.5 C

A: Solution: Influence line for bending moment at D: Introduce a hinge at D and a unit bending moment…

Q: A steel bearing needs to be mounted on a shaft with 40mm diameter, the bearing needs to be heated up…

A: Given data - Cofficient of linear expansion of steel = 13×10-6 /K do = 40 mm ∆T = 49°C Find out…

Q: Problem 1: Determine the magnitude of the resultant force per meter length acting on the…

A:

Q: Current Attempt in Progress A 1-m-diameter cylindrical mass, M, is connected to a 2-m wide…

A: To find out the required value of M.  Where,  B = 2 m H = 2.5  D = 1m

Q: Q/ Find the reaction forces at point (B)

A: Given Data:W=300kg= 300×9.81=2943NL=3.6m

Q: Two coaxial cylinders 250 mr high have a liquid in between them, the outer cylinder had internal…

A:

Q: Problem 1: Determine the magnitude of the resultant force per meter length acting on the…

A: Given-a cylindrical gate subjected to a fluid pressure. Required- to find magnitude of resultant…

Q: Q.13.17 -For the frame shown below, the initial displacement is 25 mm and the initial velocity is 13…

A:

Q: 1750 QUESTION 3 3.1 A Distance of 82,400 m between two pegs was attained with a 100 m sto tape that…

A: Note: Hi! Thank you for the question As per the honour code, We’ll answer the first question since…

Q: 1) The spool has a mass of 50 kg 1.30 m. It rests on the which the coefficient of sta coefficient of…

A:

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.