Q.1 A piston-cylinder device operates 1 kg of fluid at 20 bar pressure. The initial volume is 0.1 (the last digit of your id.no). The fluid is expand reversibly following the process pv¹.3 = constant. at point B the volume becomes 1.5 m³. The fluid is then cooled at a constant temperature. Calculate the work done in the cycle. p (bar) 0.1: last digit of your id. no 0.1 v cu.m Py 1.3 B 1.5

Q.1 A piston-cylinder device operates 1 kg of fluid at 20 bar pressure. The initial volume is 0.1 (the last digit of your id.no). The fluid is expand reversibly following the process pv¹.3 = constant. at point B the volume becomes 1.5 m³. The fluid is then cooled at a constant temperature. Calculate the work done in the cycle. p (bar) 0.1: last digit of your id. no 0.1 v cu.m Py 1.3 B 1.5

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Note:- • Do not provide handwritten solution. Maintain accuracy and quality in your answer. Take care of plagiarism. • Answer completely. • You will get up vote for sure.
19. A spacecraft, traveling in deep space, fires thrusters to achieve a change in speed of 2.8 km/s. If the specific impulse of the thrusters is 300 s, what is the ratio of the initial spacecraft mass to the spacecraft mass after the thrusters have fired? a. 0.9 3000/2.8 2.6 C. 8.2 d. None of the above 20. The state vectors for an Earth-orbiting spacecraft at a given point in tim 5
Question 4. Solve with detailed solutions please. Thank You
5. Air enters a compressor at a rate of 0.5 Kgs¹ with a velocity of 6.4 ms', specific volume 0.85 m³Kg¹ and a pressure of 1 bar. It leaves the compressor at a pressure of 6.9 bar with a specific volume of 0.16 m³Kg¹ and a velocity of 4.7 ms¹. The internal energy of the air at exit is greater than that at entry by 85 KJKg'. The compressor is fitted with a cooling system which removes heat at a rate of 60 KJs¹. Calculate the power required to drive the compressor and the cross- sectional areas of the inlet and outlet pipes.
FInd the QUESTION 4 The following processes occurs in a reversible thermodynamic cycle 12 Reversible polytropic compression at pressure 0 8 bar at volume 0 07 m³ to a pressure 11 bar and specific volume 0 6 m/kg The index of compression may be taken as n 2-3 Reversibly expansion with expansion index of 2 to pressure 2 3 bar 31 Reversible cooling at constant volume to the initial state Calculate the mass of fluid present to 3 decimal places QUESTION 5 The followin
I need questions d and e
Gas supply line- Gas A 2.1 m3 tank initially contains a gas at 170 kPa, 370 K. The tank is connected a line carrying same gas at 1700 kPa and 370 K. What should be heat transfer during this process, in kJ, so that the final pressure and temperature are 1700 kPa and 370 K, respectively. (cp=D0.92 kJ/kg.K, c=0.64 kJ/kg.K).
Write you solution neat and complete Please writh the basic formula before solving. second law of thermodynamics. Carnot cycle. please answer it in 1hr.
For a steady flow process, the rate of change in the total energy of the system will be zero. Select one: O a. True O b. False Equation of the first law of thermodynamics is O a. Internal Energy Heat rejected into work done O b. Internal Energy-Heat added plus work done O c. Internal Energy Heat added into work done Od. Internal Energy= Heat added divided by work done
Thermodynamics: Assume temperature t1, pressure p1 and p2 (i.e chose your own values).
b) Steam generators are a type of heat exchanges that are used in power plants to generate steam at desired pressure and temperature (Fig. Q1.b). In a steam generator, saturated liquid water at 30°C enters a 60-mm diameter tube at the volume flow rate of 12 L/s. After exchanging heat with hot gas, the water changes to steam and leaves the generator at a pressure of 9 MPa and a temperature of 400°C. During this process, the diameter of the water/steam tube does not change. Steam out Gas out Hot gas in Liquid water in Fig 2. Schematic of the steam generator in Q1.b. (i) Calculate the steam mass flow rate (ii) What is the inlet velocity of the steam? (iii) What is the exit velocity of the steam? (iv) Calculate the rate of heat transfer (in MW) required to change the phase of liquid water to steam.
1. Find the thermodynamic property value requested for each of the following. Enthalpy and entropy are mass-specific values. Also tell me what you have – ideal gas, superheated vapor, saturated vapor, saturated liquid-vapor mixture, saturated liquid, or compressed (subcooled) liquid. C. Find the specific volume for liquid water leaving the feedwater pump at a pressure of 120 bars and a temp of 90 °C. Use tables for steam (water)