Q: What is the bearing of course CD and DE?

Q: State the depth of improvement ?

A: Soil engineering improves techniques to enhance the soil or ground. Vibro- compaction could be a…

Q: Define the term capillary fringe.

A: The capillary fringe is characterized as the saturated zone of water immediately just above the…

Q: Figure 2.5.3 - Qu Inside perimeter Outside perimeter Centreline

A:

Q: Ep = (Ea x cotß) + (Eb x cota) + Na - Nb cot a + cot 6 (Na x cot6) + (Nb x cota) - Ea + Eb Np = cot…

A: Derivative: Derivative of Ep : Derivative of Ep is denoted as dEp Given that Ep =(Ea*cotβ)…

Q: Define Flood loads

A: The load expected to occur in case of floods due the the flood waters is called flood load. This…

Q: 2. cos2xcos7xdx

A: Consider the given equation ∫cos2xcos7xdx Use the identity cosxcosy=12cosx+y+cosx-y…

Q: What are Submerged kerbs ?

A: City roads have a component called kerb . Its a sloping or vertical component provided along the…

Q: A horizontal curve on a three-lane highway with 12-ft lanes has a PC located at station 10+00 and PT…

A: 3 lane road with 12 ft lanes  = 25o e = 4% or 0.04Clearance distance = 40 ft

Q: Define what is Two-way shear ?

A: One way shear One way shear will be ruling in linear structures like beam, combined footing…

Q: QUESTION TwO (a) Determine the side widths and areas of the following cross sections:- Fill section…

A: Given : Fill section consisting sides with slopes 1 in 3 and 1 in 3 Bottom side 1 in 10 Central…

Q: Explain pipe earthing

A: Brief concept- Earthing- It is a process by which charge is transferred to the earth with the help…

Q: 50 ↓ 50² 50k $50* a M b 6 at 25 ft 150 ft 50k 25 ft PROBLEM: DETERMINE a,b,AND C BY METHOD OF…

A:

Q: Determine maxium principal plane

A: We have to determine the maximum principal plane.

Q: What is the length of the vertical piece halfway between C and D in feet? B 12'-0" A 16'-0" D 16'-0"…

A:

Q: Compute the sinA =0.4785 cosB= -0,52d -0.52d %3D tanc= 0 987

A: Converting the given values into the degree is a very simple and easy way. We can convert the given…

Q: What is shear starin rate?

A: Shear rate:

Q: What is base flow separation?

A: It is required to answer about what is base flow separation?

Q: final bearings must be written along the appropriate lines be

A:

Q: Define Vertical Stresses.

A: The total vertical stress acting at a point below the surface of the ground is due to the weight of…

Q: 405 E= 200 CDA I= 19 X 10 4. A 2m 4m at C. C P. the to teation S'D. Ball Pen 1423

A:

Q: Bb Course Mail- myct/itemView?assignment ProblemID=15609916&offset=next Max FBC = As shown, a truss…

A: Find the force in member BC by method of sections

Q: In certain building operation, it was necessary to remove a portion of B hall which was…

A: Calculate the volume of the above solid with the help of the prismatoid formula: where; V is the…

Q: What is over-consolidated?

A: There are 3 types of consolidation stages namely : 1- over consolidation stage 2- normal…

Q: Substantial completion of a project is when: O The roof placement is completed. O 10 days prior to…

A: Substantial completion of a project is when: Answer  The owner can begin to occupy and use the…

Q: True or False: Designing earthquake-resistant buildings will help save lives when earthquakes hit. A…

A:

Q: Define Water and stream loads

A: 1. Stream Load - It is defined as all the sediments carried by the stream of water with it. It can…

Q: Please Create section AA' and BB' on autocad.

A: We need to first obtain the 3D model of given drawing using the following steps and then create…

Q: 2) An 8m steel tape was purchased and advertised as follows: Standard temperature Standard Pull Таре…

A:

Q: 4#8 12" 15" I 3: fó= tooopsu Grade Go Steel NWC. &Mn = ?

A:

Q: Building codes are concerned primarily with public safety, an provide maximum design and…

A: Solution; I want to tell you that public safety and other considerations are always in the building…

Q: What is ASD method

A: Allowable Stress Design (ASD) It is also known as the service load design or working stress design…

Q: WOULD THE BEARINGS BE THE SAME?

A: Finding the bearings of a line AB, BC, CD, DA. In above solution find out the azimuth of lines is to…

Q: CONSTRUCT 4 A 4B A SUMMARY TABUL & PLOT Fc = 6000 PS1 fy = 60 ks2 Fe 4000 PS1 Fy = 60 KSI 23 26 14"…

A: Beam AWidth= 14in ; Eff. Depth= 20.5in ; depth of NA= 4.45in ; Strain in concrete= 0.003 ; Strain in…

Q: Problem 3 Compute the nominal compressive strength of the member shown. Use the theoretical value…

A: Given Data:Member HP 16×121                        A572 Grade 55Length of member = 14 feet To…

Q: How are finished grades determined in machine guidance and control?

A: .Today’s machine-control systems help operators of all skill levels get to finished grade faster by…

Q: ] Use graph paper to draw simplified sketch of the gear and the rack shown in problem 5/64(79). What…

A: Figure is as shown

Q: Evaluat the fllowing limits Lim X # a X>a X - a

A: Given values -  limx→a = x2+1 - a2+1x-a     ,    x ≠ a   Rule -  The above problem can be solved by…

Q: PROBLEMS, DETERMINE To ALL FOR AFD, SFD, THE AND BMD MAKING SURE SHOW AU WORK REQUIRED To OBTAIN…

A: We will find reactions at A and D and draw FBD to solve

Q: What is Uniformly loaded strip ?

A: Answer:- Uniformly loaded strip: A uniformly loaded strip is defined as that strip which is…

Q: What is VMT?

A: as the acronyms having the various meaning for VMT.  but some important term is used in civil…

Q: Define Earth pressure loads

A: Pressure is defined as force acting per unit area of the body.

Q: (2 2' 3 4 8570 PROBLEM 1 2720 3580 1500 (A 202 1 2 The Figure on the right is a 2nd Floor Structural…

A: To find one way or two way slab

Control Survey and Geodetic reductions

Control surveys or survey controls are used to establish reference points as a basis for various construction activities. Vertical and horizontal control points are to be established in a control survey to increase accuracy. After establishing the control points, all other types of surveys such as topographic, right-of-way, aerial mapping, construction layout, boundary surveys, and utility mapping can be worked upon so that control networks can be formed. The place from which the observations are made is called a survey station.