Q/ The wave impedance of the TE10 mode of an air-filled rectangular aveguide at a frequency of 15 GHz is given to be 480 2. a- Calculate the cutoff frequency for the TE10 mode of this waveguide b- Calculate the 'a' dimension for the waveguide c- Calculate the cutoff frequency for the TE mode for this waveguide assuming b-0.4a d- Calculate the wave impedance at the frequency of 15 GHz for the TE10 mode if the above waveguide is filled with a dielectric with &-2.5

Q/ The wave impedance of the TE10 mode of an air-filled rectangular aveguide at a frequency of 15 GHz is given to be 480 2. a- Calculate the cutoff frequency for the TE10 mode of this waveguide b- Calculate the 'a' dimension for the waveguide c- Calculate the cutoff frequency for the TE mode for this waveguide assuming b-0.4a d- Calculate the wave impedance at the frequency of 15 GHz for the TE10 mode if the above waveguide is filled with a dielectric with &-2.5

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What does the TE mean? Why does one have a 10 as subscript and the other mn? What is a broad and short dimension and a rectangular waveguide?
4. Again, from the zigzag-path waveguiding model, explain why the group velocity is always slower than the phase velocity in a waveguide with a cutoff frequency.
A 2 V signal is incident to the interface from a 75 Ohm region propagating to a 50 Ohm impedance region. What is the reflection coefficient? What is value of the incident, reflected and transmitted wave? What voltage would you measure on either side of the interface right after the signal goes through the interface. For the interface, I'm a little confused. I used a voltage divider and got V_transmitted = 0.8 and V_incident = 1.2. But shouldn't they be the same?
A 2.28-cm by 1.01-cm waveguide is filled with a dielectric material with er = 2.25. The waveguideoperate at 15GHZ. For TE11 and TE02 mode which mode will propagete.
P 2.7a What will be the cutoff wavelength for dominant mode in rectangular waveguide whose length is 10 cm? (2)
Why does TEM mode cannot propagate in rectangular waveguides?
Sketch/Draw the following: a. 100% modulation trapezoidal pattern b. Negative Carrier Shift c. Envelope of a square wave modulating a sinusoidal carrier
what are the modes of waveguide from where does they origionate?
What is field pattern in a. Rectangular waveguide?b. TE mode in rectangular waveguide?c. TM mode in rectangular waveguide?
For dominant mode propagation in TE mode, if the rectangular waveguide has a broader dimension of 31.14 mm , then the cut-off wave number: a) 100 b) 500 c) 50 d) 1000
This question from micorowave system course.
3. Coaxial cable is used in applications requiring the propagation of high-frequency signal. Such cable consists of a solid conducting cylinder as the inner conductor and a solid conducting cylindrical shell as the outer conductor. A dielectric fills the region between these conductors. Consider the RG-59/U coaxial cable that is commonly used to connect a television/internet equipment. It has an inner conductor with a diameter of 0.584 mm, dielectric filler with a dielectric constant of K = 1.20, and an outer conductor with an inner diameter of 3.7084 mm. Assuming that these conductors are very long, calculate the capacitance per metre of the RG-59/U coaxial cable. Include a derivation of an equation for the capacitance per unit length of the coaxial cable and then use this equation to calculate your answer. (As discussed in class, assign a charge +Q and voltage V to the inner conductor and a charge -Q and 0 V to the outer conductor, solve for the voltage V, and then compute the…