Q) A two-segment shaft is used to transmit power at constant speed through the pulleys shown above and to the right. Power is input to the shaft at B through a torque of Ts= 230 N-m. A torque of T4= 60 N'm is observed at 4, and a torque of Te=170 N-m is observed at C. The external torques act in the directions indicated in the figure. Both shaft segments are made of phosphor bronze [G= 42 GPa] and both segments are solid shafts. Segment (1) has a diameter of di = 20 mm and segment (2) has a diameter of d;= 35 mm. a. Determine the torque observed in segments b. Determine the maximum shear stress observed in the shaft c. Determine the angle of twist observed in segments

Q) A two-segment shaft is used to transmit power at constant speed through the pulleys shown above and to the right. Power is input to the shaft at B through a torque of Ts= 230 N-m. A torque of T4= 60 N'm is observed at 4, and a torque of Te=170 N-m is observed at C. The external torques act in the directions indicated in the figure. Both shaft segments are made of phosphor bronze [G= 42 GPa] and both segments are solid shafts. Segment (1) has a diameter of di = 20 mm and segment (2) has a diameter of d;= 35 mm. a. Determine the torque observed in segments b. Determine the maximum shear stress observed in the shaft c. Determine the angle of twist observed in segments

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2) A shaft of a diameter of 30 mm is transmitting 14,9 kW at 400 rpm. The shaft is connected to a pulley of an axial length of 160 mm with the help of a rectangular key 16 mm x 12 mm ( b=16 mm, t=12mm). (The spokes are connected to the pulley, but the pulley is not shown in the figure). Axial length of the key, hub and pulley are 160 mm. Determine the shear and normal stresses developed in the rectangular key. Rectangular key Spokes A R Hub Shaft
A steel 0.75-in diameter shaft (G= 12,000 ksi) is subjected to the following torques in lb-ft: TA = 50; TB = 70; TC = 30; TD = 10. The directions of the applied torques are indicated in the figure. The bearings shown allow the shaft to turn freely. The length of each segment is equal to 38 in. (a) Plot a torque diagram showing the internal torque in segments (1), (2) and (3) of the shaft. Show the FBD of each segment using a double-headed arrow to represent each torgue. Use the same rule of signs as in the lecture. Determine (b) the maximum shear stress magnitude (ksi) in the shaft. (c) the rotation angle, in degrees, of pulley D with respect to pulley B. Note: Follow the rule of signs with FBD in each sections. Show complete step by step solution and proper FBD. Solid shaft: J = (₶/32 )( D4) Hollow: J = (₶/32)(D4 - d4)
A fixed-end shaft is subjected to torques T1 (Nm) and T2 (Nm) as shown in the figure. If the shear modulus of elasticity is Gahat= 20 GPa, and shaft diameters are D, (mm) and D2 (mm) determine the angle of twist at point C, ØCIA- D1=100mm D2=30mm T1=800NM T2=200NM D1=100mm T(Nm) B D2=30mm |T;(Nm) A L=300mm Section for point A =900mm Section for points B and C Results Table ОСА (rad.)-
In the figure below, a motor with power 150kw and speed of 2500 rpm is connected to shaft 1(by coupling) in a clockwise direction. Shaft 2 is connected to shaft 1 by gears 1 and 2. If 30% of the power is consumed by the gear3 and 9% by the pulley and 61% by the sprocket, draw torque diagrams for both shafts. • Lengths: AB=90mm/BC=GH=50mm/CD3HI=60mm/DE=IJ=80mm 13 Gear3 E Gear2 14 15 16 Motor shafth 2. 17 Bearing Shaft1 Gear1 sprocket
3) Two circular shafts (shown in Figure) made of the same material and have the same length are subjected to a torque Tequals 150 lb.ft, the angle of twist for the hollow shaft equals that of the solid shaft. A-1/3 C-5.4 B-1 D-3 D=10 in solid shaft D=10 in d=9 in O hollow shaft
I need Question 5.2.3 &5.2.4
A solid steel [G= 12900 ksi] shaft with the diameter of d = 1.375 in. is subjected to torques TB = 250 lb.ft, TC = 300 lb.ft, and TD = 140 lb.ft, acting in the directions shown in the figure. Assume a = 48 in., b = 74 in., and c = 40 in. Determine the rotation angle of pulley C with respect to the support at A. In rad
3) Two circular shafts (shown in Figure) made of the same material and have the same length are subjected to a torque Tequals 150 lb.ft, the angle of twist for the hollow shaft equals that of the solid shaft. A-1/3 C-5.4 B-1 D-3 D=10 in solid shaft D=10 in d=9 in O hollow shaft
A maximum torque of 6.75 kNm can be supplied to the constant diameter steel (G= 80 GPa) line shaft by a motor as shown in Figure Q2. At the current normal operation condition, three machines are driven by gear B, C and D on the shaft and they require torques of 3.x kNm, 1.5y kNm and 1.0z kNm, respectively. Parameter x, y, and z are given by: Q2 X=0 Y=0 Z=2 Considering the maximum torque can be supplied by motor, determine the minimum diameter required if the maximum shearing stress in the shaft is limited to 100 MPa. Round your answer to the nearest whole number. (a) -Bearing D Figure Q2
A solid constant-diameter circular shaft is subjected to the torques of TA = 560 lb·ft, TB = 1080 lb·ft, TC = 850 lb·ft, and TD = 330 lb·ft, acting in the directions shown. The bearings shown allow the shaft to turn freely.(a) Plot a torque diagram showing the internal torque in segments (1), (2), and (3) of the shaft. Use the sign convention presented in Section 6.6.(b) If the allowable shear stress in the shaft is 4200 psi, what is the minimum acceptable diameter for the shaft?