Q-5) A unity feedback system has the following forward transfer function: 1000(s + 8)(s + 12) s(s+ 15)(s² + 2s +28) G(s) a. Evaluate system type, Kp, Ky, and Ka. b. find the steady-state errors for the following test inputs: 25u(1), 7u(), 47и().

Q: Thanks for your helping

A: It is our pleasure that you get what you were looking for.

Q: Can you please picture the solution again? because it's too vague, I can't read very well. Thank…

A: It is asked to picture the provided solution again.

Q: Thevenin and Norton Equivalent: 15). For the circuit in Fig. 4.109, find Thevenin equivalent between…

A: We need to find out thevenin equivalent circuit and norton equivalent circuit

Q: Which is a better source of information, the power supply or the DMM? Why?

A:

Q: explain insulation coordination and write method of insulation coordination

A: We have to explain insulation coordination and write method of insulation coordination.

Q: Explain the importance of residual voltage in a dc generator. Note: Figures and sketches are…

A: Given: Explain the importance of residual voltage in the DC generator.

Q: What is sourcing current, and its connection to switching of power? It's confusing. Please help.

A: Power: It is amount of energy which transferred per unit time, it means rate of doing work. It is a…

Q: Hi,  Are you able to go into some more detail on its opperation if possible.

A: Given: To explain: The operation of the circuit as a NOT gate.

Q: Coriolis flow meter is a type of -------- flow meter.

A:

Q: * Q) DC bridge are used for measurement of capacitance. O measurement of current. O measurement of…

A: DC bridges

Q: what was the calculation done to get d? Confused on how this was rearranged.

A:

Q: I dont get it. howcan I make sure its in low condition?

A: You have asked that how to make sure it is in low condition.

Q: Should the correct answer be 3 decibals?

A: here we have to find the voltage gain for the given power gain.Here we assume that input and output…

Q: Can you help me with questions two and three please?

A: Present StateNext State (UP)Next State…

Q: please tell me last part answer

A: let Z = a+jb  then a is called real part and b is called imaginary part .

Q: 4. Bus bars are either flat tubes as these shapes allow heat to or dissipate more efficiently.

A: The size of bus bar determines the amount of current flows through it safely. The heat dissipation…

Q: Please answer in typing format

A: The Peltier effect is the result when electric current is passed between two materials,such that it…

Q: What are the basic/necessary steps to design a pico hydro power plant? Inlcude the parts of…

A: The basic/necessary steps to design a pico hydropower plant: • It should be practical and suitable,…

Q: What is the area of ​​the shaded part

A:

Q: L{7te¬5t cosh(3t) + +sin(Võt) – rº + e%}

A:

Q: question: Suppose that you want to sort blocks of different heights automatically. How can this task…

A:

Q: What is the scientists trying to solve these problems?

A: The question deals with overcoming the disadvantages of perovskite solar cells.

Q: where is the value of 10/sqrt(2) coming from?

A:

Q: 13-Find the Thevenin and Norton equivalent circuits between ab. 2 A a 6 0 18 V 3 A 10 V

A: Given:

Q: Problem 1 is a review of your understanding of KVL (Kirchhoff's voltage law) Using KVL find the…

A: A simple question based on network analysis and the topics described in the solution are kirchoff's…

Q: The circuit shown in Figure Q5.1 consists of a current source connected to a load via a cable. The…

A: Given circuit is - Value of current source is -

Q: in this Lab you will be laying out and installing an emergency service panel. Emergency service…

A: (1)  Legally Required standby systems provide electric power to selected loads during firefighting…

Q: If Be = 1.1 Tand Hc = 260 A-t, then the relative permeability is: Hr=

A: Flux density, Bc = 1.1T Magnetic field intensity, Hc = 260 A-t

Q: Vdc0 U=12 V Circuit #1 Ried LED www Ried_series Vdc0 U= 12 V Current in LED (A) Circuit 0.03 #₂ 0.02…

A: Given Data:An LED illumination circuit with,Supply voltage Set-current of the diodes V-I…

Q: 1) Given the figure and values below: R = 5.6 kfl , Rc = 4.7 kil , Rg = 1.2 kfl, Vcc = 18 V, Vc = 12…

A:

Q: you tell me how circuit breakers and diconnect switches are used to isolate equipmen

A:

Q: What is the unit E?

A: In the given question, the source voltage has a magnitude of ε Volt.

Q: Explain what this matching box is. Describe the parts

A: The given diagrams are shown below. It is asked what is this matching box and also it asked to…

Q: explain the Reasons for coordinating electrical protections

A:

Q: this is not incomplete, and please do not answer its functioning of parts answer should be on point…

A: It is asked to explain the isolated operation of wind farms.

Q: 3 What is a Pump Storage Hydro Power Plant? Explain briefly.

A:

Q: An electric field is given as E=x(y+1)+y(z−1)+22 Verify that the field is indeed an electrostatic…

A:

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.