Q 1(c) The frequency spectrum of an input signal and the frequency-domain impulse response of a filter (a Linear Time Invariant system) are shown in Figure 2. Plot the frequency spectrum of the output of this filter for the input signal shown. Amplitude 1.0 0.5 0.0 200 Figure 2 Input Signal 220 240 260 280 Frequency (Hz) 300 Amplitude 1.0 0.5- 0.0 200 System Impulse Response 220 240 260 280 Frequency (Hz) 300

Q 1(c) The frequency spectrum of an input signal and the frequency-domain impulse response of a filter (a Linear Time Invariant system) are shown in Figure 2. Plot the frequency spectrum of the output of this filter for the input signal shown. Amplitude 1.0 0.5 0.0 200 Figure 2 Input Signal 220 240 260 280 Frequency (Hz) 300 Amplitude 1.0 0.5- 0.0 200 System Impulse Response 220 240 260 280 Frequency (Hz) 300

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1) a) A 1V 5 kHz signal is put into a low pass filter with a cut-off frequency of 2 kHz. What will the frequency of the output signal be? b) A 1V 15 kHz sinewave signal is put into a low pass filter with a 2 kHz cut-off frequency. The output signal will have how much amplitude approximately?
The output power of filter is 100 mW, when the signal frequency is 5 kHz. When the frequency is increased to 25 kHz, the output power falls to 50 mW. What is the dB change in power ?
Transmitter: a carrier frequency of 108 kHz and a modulating frequency of 0.3 kHz to 3.4 kHz is applied to an amplitude modulator. The USB and the LSB are both transmitted to the distant receiver, with a suppressed carrier. Receiver: the resultant USB and LSB from the transmitter are input to an amplitude demodulator. A carrier frequency of 108 kHz is reintroduced to the demodulator. Determine the following: 1. The LSB and USB at the output of the modulator. 2. The LSB and USB at the output of the demodulator.
Q2- Explain by equations and block diagram the direct method demodulation in NBFM Q3- Write the formula of the phase modulation (PM) when Ac=25 , Fc=10® Hz, Kp= 20 . If an information signal m(t) = cos(212000t) + 10sin(2n2000t) Q4- Drive a formula for NBFM by using Bessel function Q5- If an information signal X(t) = cos(2n700t) + 10cos(25000t). Write the formula of the frequency modulation (FM) when Ac=20 , Fc=10® Hz, Kf= n2000 Q6-) If NBFM signal passes through a frequency multiplier. With B < 0.5 and fc=200kHz. Let fm ranges from 50OHZ to 15kHz, and let the maximum frequency deviation Afat the output be 75kHz. Find the required frequency multiplication n and the maximum allowed frequency deviation at the input. Q7- If an angle modulated signal S(t) = 10[cos(210®t) + 15sin(2n10³t)]
Brief explanation of kalman filter
What percent reduction in output/input signal magnitude would you expect at the 1800 cycle/min frequency from a thermocouple with a 1/9 of a second time constant? Assume T= 3 and static sensitivity, K 1. 30% 5% 70% 95%
Q1.B) Explain why active filters are designed as biquadratic sections ?
The figure below shows a phase shift oscillator with amplitude control. Design the circuit to produce 7kHz frequency and a ±8V output waveform. Assume that I1 = 1mA and R2=R3. Do your design on a piece of paper and then enter the various resistor and capacitor. NOTE: Use only E24 values for your design Enter the values of R1=_____Ω, R2_____kΩ . , R3._____kΩ , R4._____kΩ . , R5_____kΩ , R6_____kΩ and R7 _____kΩ and the value of C=_____ μF
FM modulated signal is demodulated using: Select one: O a. Costas PLL O b. Carrier reinsertion method Oc Discriminator followed by integrator O d. Discriminator A Phase-locked loop can be used as: a. FM modulator O b. AM demodulator O c. AM modulator d. FM demodulator
Which of the following is not a part of the PLL O a. Loop filter O b. phase detector O C. Differentiator O d. Voltage controlled oscillator Which of the following statements is not correct: a. A third-order PLL can track a frequency step with zero steady-state error. O b. A first-order PLL can track a frequency step with a zero steady-state error. O c. A first-order PLL can track a phase step with a zero steady-state error. O d. A second-order PLL can track a frequency step with zero steady-state error. %24
Q)Design a Discrete Time Low Pass Filter for a signal. Butterworth Filter. Chebeyshev Filter The specifications are:(Voice Signal) 1) Passband Fp = 4 kHz, with 0.2 dB ripple; Stopband FS 4.5 kHz, with 45 dB ripple. Sampling Frequency Fs = 22 kHz. (Use For Both Filters). 2) passband ripple - 0.2 stopband ripple 45 passband frequency 1300 stopband frequency = 1500. sampling frequency=10000. (Chebeyshev Filter) 3) Passband ripple=0.5 stopband ripple 50 passband frequency 1200. stopband frequency = 2400 Sampling Frequency= 10000. (Butterworth filter)." 4)Choose your own Specifications
Q17. The circuit shown in figure Bl17 is used to amplify wide band of frequency from 20KHZ to 150MHZ. Assume Vcc=20V, VCE= 4.5V, Is=70µA, Ik-8.5mA and Zin=2702. Design the value of Resistors. i) R1. ii) Rc and RE. Output Input Signal Figure B17 ww ww- ww