Procedure (A) Buck Converter (Duty Cycle) 1. Make connections of power supply, capacitor, inductor, MOSFET and load resistor to build the buck converter. Vs=100 V=18 r=0.5% R=10 ohm f=40 KH Calculate minimum inductance: Lmin=(1-D)( R)/2f Calculate minimum capacitance: Cmin=1-D/8L(AVo/Vo) f^2 Calculate duty ratio: D=Vo/Vin

Procedure (A) Buck Converter (Duty Cycle) 1. Make connections of power supply, capacitor, inductor, MOSFET and load resistor to build the buck converter. Vs=100 V=18 r=0.5% R=10 ohm f=40 KH Calculate minimum inductance: Lmin=(1-D)( R)/2f Calculate minimum capacitance: Cmin=1-D/8L(AVo/Vo) f^2 Calculate duty ratio: D=Vo/Vin

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ: A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating...

See similar textbooks

Similar questions

A 5uF capacitor is connected across an emf of 50 Volts maximum value and frequency of 1000 cycles. What is the equation of the current?
1. Enumerate five formulas for series-parallel capacitances across Vt source and draw the circuit. 2. Enumerate five formulas for parallel-series capacitances across Vt source and draw the circuit.
low voltage systems What is the general reason for selecting the capacitor voltage with a value greater than 400 V (such as 415,445 V) in Reactive Power Compensation? a) Reduce losses b) Harmonics C)Current decrease d) Voltage drop
1.Enumerate five formulas for four series connected capacitances across Vt source and draw the circuit. 1. Enumerate five formulas for four parallel connected capacitances across Vt source and draw the circuit.
An inductor of 150hms and resistance of 10 Ohms are connected in series to a 230V, 50 Hz ac supply. Determine the active and reactive power and power factor in the circuit.
Using a positive Clamper Circuit, with an AC voltage of Vi = 100v with a frequency of 30hz, a value of 1000u for the Capacitor, a silicon diode and a resistor with the value of 100 ohms. Find the voltage value on the resistor at a simulation of Oms. Vm 2Vm Mr. Vm Vo -Vm Input Waveform Output Waveform Positive Clamper circuit
Using a positive Clamper Circuit, with an AC voltage of Vi = 13v with a frequency of 60hz, a value of 100u for the Capacitor, a silicon diode and a resistor with the value of 1000 ohms. Find the voltage value on the resistor at a simulation of 20ms. 2Vm Vm Vm Vo -Vm Input Waveform Output Waveform Positive Clamper circuit
The voltage signal coming out of the capacitor is with small ripples compare to the voltage signal out of the diode. True False
Using a positive Clamper Circuit, with an AC voltage of Vi = 100v with a frequency of 30hz, a value of 1000u for the Capacitor, a silicon diode and a resistor with the value of 100 ohms. Find the voltage value on the resistor at a simulation of Oms. Vm 2Vm Vo -Vm Input Waveform Output Waveform Positive Clamper circuit
What voltage is boosted at the output of a multiplier.Choices: average, rms, peak, or instantaneous Which assumption is not used in the analysis of multipliers?Choices: a capacitor will not discharge, start with the cycle of the source that will forward bias the nearest diode, the output will always be multiplied, or a single diode is forward biased at a time A voltage multiplierChoices: multiplies the output voltage, has very high voltage and low current ,can employ inductors, or may not have equal numbers of diodes and capacitors A voltage regulator maintains constant voltage at the load regardless of variations atChoices: the input and output, the load, source, or in the environment Between a lower percent regulation and a higher one, which is better?Choices: lower or higher
A thyristor switched capacitor consists of: A. A fixed capacitance and a relatively small a relatively small surge limiting inductance B. A fixed capacitance and a relatively large surge limiting inducatance C. A variable capacitance and a relatively small surge limiting inductance D. A Variable capacitance and a relatively large surge limiting inducatnce
Full-wave rectified sine wave circuit is used to measure the RMS value of a half square wave with the help of PMMC meter. The meter was actually calibrated for sine wave. The circuit uses a meter movement with a full scale deflection current of 200uA and internal meter resistance of 5kΩ. Assuming Non-ideal diodes having resistance 1kΩ, Analyze the circuit to determine the value of series multiplier resister and the corrected RMS voltage, if meter is to read 225V RMS full-scale.