PROCEDURE: 1. Ignition Tests A. Flammability a. Place 2 to 3 drops of 95% ethyl alcohol solution in a watch glass. Light the alcohol and note the nature of the flame produced. Result : b. Repeat the experiment using water instead of alcohol. Result : В. Charring a. Place a pinch of brown sugar in a dry evaporating dish and heat gently over a small flame until a change is noted. Now heat strongly until the material turns black. What do you think is the material left? b. Repeat using a pinch of NaCl instead of sugar. Heat as before and see what happens to the salt. Did it char? Was there any sign of melting? What can you say about the resistance of organic and inorganic substance to heat?

PROCEDURE: 1. Ignition Tests A. Flammability a. Place 2 to 3 drops of 95% ethyl alcohol solution in a watch glass. Light the alcohol and note the nature of the flame produced. Result : b. Repeat the experiment using water instead of alcohol. Result : В. Charring a. Place a pinch of brown sugar in a dry evaporating dish and heat gently over a small flame until a change is noted. Now heat strongly until the material turns black. What do you think is the material left? b. Repeat using a pinch of NaCl instead of sugar. Heat as before and see what happens to the salt. Did it char? Was there any sign of melting? What can you say about the resistance of organic and inorganic substance to heat?

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

How can you remove insoluble impurities during a recrystallization? options: 1-Hot gravity filtration. 2- Vacuum filtration 3- It is not possible.You should choose another separation method. 4- Pick out the impurities with tweezers.
QUESTION 20 Match following waste with the proper waste container. Used capilary tube after m.p. determination A. Aqueous waste Excess bromoethane B. Halogenated organic waste Diels-Alder reaction product Solid waste container Aqueous layers after each extraction in acid-catalyzed hydration D. Regular trash * Used plastic disposable pipets E. Broken glass contalner QUESTION 21 In hydroboration-oxidation experiment. 0.375 mL 1-hexene (density 0.673 g/mL mdtar mass 84.1608 g/mol). 1.110 ml of BH3 THF (molarity of BH3 is 1.00 M. and 0.294 ml of H0, solution (30.0% w/w. density 1.11 g/mt. molar mass 34.0147 g/mol) are used. Final mass of 1-hexanol (molar mass 102.177 g/mo) is 0.1681 E What is the percent yield of this reaction? Note: In the final answer, you need to input % mark after the value. Pay attention to numbers of significant figures
5.EPS made from------ 1.polystyrene 2. monomer styrene 3. photolysis 6.Thermal insulation has greatest potential for reducing----- 1.C01 2.CO2 3.03 7.Reason of clay Bricks contain-----whit crystals that appear irregular. 1.soluble salt 3. light material 2. binding coarse 8. Gable window are provided in gable end of - ‒‒‒‒‒ 1.floor 2. frame 3. roof 9.Failure occurs in long column due------ 1.lateral instability 2. axial load 10.TO decrease the soluble salt inside brick using------ 1.drying 2. saturation 3. soaked 3. material failure
Procedure:1. Mix the flour, sugar and one cup of warm water together in the bottle.2. Cover the top of the bottle with the balloon, and then observe for a few minutes.3. Add the yeast to the remaining half cup of warm water in the glass.4. Remove the balloon and add the yeast-water mixture to the bottle. Stir the mixture using barbequestick.5. Seal the bottie by putting back the balloon. Observe every minute.Question for Analysis: 1. What did you observe after the yeast was added to the mixture?2.Yeast contains enzymes. Why enzymes considered catalysts?
Lab Activity: Isolation of Lycopene from Tomato Paste What is the drying agent that should be used? Calcium chloride or anhydrous magnesium sulfate?What is the purpose of this drying agent? Explain
Which of these statements regarding dissolved gas analysis is incorrect? Select one: A. For low temperature faults methane and hydrogen are generated B. As the temperature of the fault increases, ethane is produced reducing the methane content C. At higher temperatures methane starts increasing overtaking the ethane content and ultimately becomes predominant D. Moisture content is measured is as free and dissolved levels
3. The TLC technique can be used to: a. Check the purity of a compound. b. Determine the number of components in a mixture. c. Purify large amounts of a compound. d. Check the identity of a compound all of the above b and d a and d a and b a, b and d
Please all parts solve
1. (Manipulation) Calculate the percent of the water absorbed relative to the mass of the polymer. Mass of the polymer= 1 gram Water absorbed by the polymer = 220 ml Calculation:
Please help me answer these subunits!
You want to make the bunsen flame spread more effectively, you'll use: a. flask b. fish tail c. wire gauze d. the adjustment knob for air entrance control *This is a multiple choice type of question