Problem The maximum stress produced by a pull in a bar of length 1 m is 150 N/mm2. The area of cross-sections and length are shown in Fig. 4.3. Calculate the strain energy stored in the bar if E = 2 × 105 N/mm².

Problem The maximum stress produced by a pull in a bar of length 1 m is 150 N/mm2. The area of cross-sections and length are shown in Fig. 4.3. Calculate the strain energy stored in the bar if E = 2 × 105 N/mm².

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A punch for making holes in steel plates is shown in Figure 3. Assume that a punchhaving diameter d = 20 mm is used to punch a hole of 8 mm plate. If force, V = 110 kNis required to create the hole, determine the shear stress in the plate.
Question The state of 2D-stress at a point is given by the following matrix of stress: [0x %]-[ 100 30 30 20 = MPa 0. What is the magnitude of maximum shear stress(Radius of Mohr's circle) in MPa?
For the state of stress shown in Figure (5), calculate the normal and shear stresses on all faces of an element at an angle 0 = 35° c.c.w. 18.88 MPa 32.27 MPa 0= 60 deg. X Figure (5) 55.89 MPa
A cross section of an engineering structure made of steel is shown in the Figure. For an applied torque of T = 175 N.m, (a) determine how much torque is carried by each of the two cross-sectional components and (b) the angle of twist per unit length. The shear modulus G = 200 GPa. (Neglect the stress concentrations). 45 mm 40 mm 4 mm 60 mm 4 mm 4 mm 120 mm 6 mm
170MPA 320MPA 430MPA Figure Q2: State of plane stress
A pressurized cylindrical tank with flat ends is loaded by torques T and tensile forces P (see figure). P The tank has an inner radius of r = 141 mm and wall thickness t = 6.5 mm. The internal pressure p = 7.25 MPa and the torque T = 820 N m. (Assume that the structure behaves linearly elastically and that the stresses caused by two or more loads may be superimposed to obtain the resultant stresses acting at a point. Consider both in-plane and out-of-plane shear stresses unless otherwise specified.) (a) What is the maximum permissible value of the forces P if the allowable tensile stress in the wall of the cylinder is 169 MPa? (Enter the magnitude in kN.) KN (b) If forces P = 400 kN, what is the maximum acceptable internal pressure in the tank (in MPa)? MPa
A stress element is subjected to bi-axial loading as shown in figure. P 30° 30° L 30° What will be the maximum principal stress for the given stress element?
An element is subjected to plane stresses as shown in Figure Q1. (i) Determine the normal stress and shear stress acting on the plane that is inclined at 20° as shown in the figure. (ii) Determine the principle major and minor stress and the orientation of the plane where the stresses acting. (iii)Determine the maximum shear stress and the orientation of the plane. 10 N/mm² 30 N/mm² 50 N/mm² 2007 50 N/mm² 30 N/mm² 10 N/mm²
B5
A rectangular piece of material is subjected to tensile stresses of 83 and 65 N/mm on mutually perpendicular faces. Find the strain in the direction of each stress and in the direction perpendicular to both stresses. Determine also the maximum shear strain in the plane of the stresses, the maximum shear stress and their directions. Take E=200 000 N/mm² and v=0.3. Ans. 3.18×10 4, 2.01×10-4, –2.22×10-4, 7max=1.17x10-4, Tmax=9.0 N/mm² at 45° to the direction of the given stresses.
The tubular shaft shown in the figure has an external diameter of D = 5.5 in. and an internal diameter of d = 2.75 in. and is subjected to a torque of T= 6825 lb-in. [theta = 31 deg] What is the shear stress at A?in psi What is the shear stress at B?in psi What is the shear stress at C? What is the shear stress at D?in psi What is the shear stress at E?in psi