Problem Statement Based on Problem 5-22 from the textbook. if the intensity of the distributed load acting on the beam is w, determine the reactions at the roller A and pin B. W mw b B

Q: -3 ft- -4 ft- 60 B 1.5 ft 500 ft-lb D 1.5 ft

A:

Q: determine the difference of elevation of points A and B

A: C value is not given. so I assumed C as 0.381. So there must be variation in the answer option…

Q: L K H 3 m A G B C E F |-2 m--2 m--2 m--2 m--2 m-|-2 m-| 20 kN 30 kN 40 kN

A: For determining forces in members of truss two methods are used which are as follows: Method of…

Q: 440 (kN) .09 2m 220 (kN/m) 4m hinge w

A: A beam is given, we need to analyse the beam i.e. finding reactions, axial force diagram, shear…

Q: A line of levels was run from point 5 to point 6, 8km apart. The average backsight and foresight…

A: Given: Average backsight and foresight distance = 100 m Distance between point 5 and point 6 = 8 km…

Q: Using the Stadia Reduction Table,what is the Cde if the instrument constant is 0.229 and the…

A: Vertical angle 21.43° Instrument factor .229 K= 100

Q: KN 4m 上 4m 100 t Kat 200

A:

Q: stadia reduction table, what is the difference in elevation if the observed vertical angle is…

A: Vertical angle 19°24" Staff intercept =s Difference in election v

Q: Assuming the conduit in the figure is a 36” wrought iron pipe flowing full, and that the outlet is…

A: Given wrought iron, the friction factor will be = 0.008Diameter of the pipe  = 36 '' It is asked to…

Q: A space force is directed from M(5,0,4) to (N(2,3,-1). If ita magnitude is 30ON, then its…

A: To find x component of 300N force

Q: Problem #4 Compute for the resultant of the given Parallel system and its relative position from…

A: Determine the resultant of the load and it's relative position from point A.

Q: Determine the horizontal force Q applied to block B that would cause the system to impend its motion…

A: Consider the F.B.D

Q: Sta. Occ. Sta. Obs. Bearing Azimuth from South 195 47'10" Distance A 9.6m C 8.91m 305 °57'63" C…

A:

Q: 45° 2m y Fig. 35

A:

Q: 25KN 3M lookN 3M の

A:

Q: he diagram below shows a rigid body ABC held in equilibrium by a ball-and-socket joint at A and…

A:

Q: (a) (b) S-diagram A C (c) M - diagram 21.39 3m 25 kN G B 1.5m 1.5m F 5 kN/m E 18.61 3m C 0.5m 20 kNm…

A: Given Load 25 kN & 5 kN/mMoment 20 kNmSpan 11 mTo find out SFDBMD

Q: YD D 7 m В 2 m 2 kN

A:

Q: 1. DIFFERENTIAL LEVELING STATION BACK SIGHT HEIGHT OF INSTR. FORESIGHT ELEVATION BM 10 4.64 209.65 m…

A:

Q: Q-2-: In the following table: a. Check all calculations. b. What order of levelling does this…

A:

Q: 400 N 2m 2m 2 m 45 P 2m

A: Note: As nothing is mentioned in this question so we are assuming that we have to calculate support…

Q: 86 \div 2

A: The numerator or dividend is the number 86.

Q: Find R1

A: Given data : The value of point load P=20 KN The value of point load Q=30 KN The value of point load…

Q: A line of levels is run from BM1 to BM2, which is 12 km long. Elevation of BM1 was found out to be…

A:

Q: Find wetted area and wetted perimeter

A: Introduction : The given question is related with fluid mechanics . In this question we are provided…

Q: 100kN is attached to the pin at A. Determine the tension in the horizontal cable. Also, determine…

A:

Q: How would I go about finding E,F?

A:

Q: 59. The back staff reading on a B.M. of R.L. 500.000 m is 2.685 m. If foresight reading on a point…

A: given- Reduced level of BM=500 mBack staff reading BS=2.685 mforesight readig FS=1.345 m

Q: of

A:

Q: 8-9 Determine the most unfavorable arrangement of the crane loads and compute the maximum and…

A: Beam and loading arrangement: To find: The maximum and minimum values of the designated quantities…

Q: Find the level of Poin A (Azimuth. OA.Oc) From the diagram below A verteal angle e = 47° 15m 4.5 B…

A:

Q: Continuation from Question no. 3: Determine the horizontal reaction at C. B 76.33 KN 75.33 KN 74.33…

A:

Q: ) pind L, and し。 a b) find H

A:

Q: +he quadrilateral measured by tape:. MEA SURING ANGLES TAPE. In ABCD WITH shown in Fig. I1-18, the…

A: Given All the length of sides of the Traverse (quadrilateral) and diagonal.  To find All the angles…

Q: The following data was obtained with the level. What is the HI of the instrument Sta. BM ΤΡΙ TP2…

A: For first part of the question the HI can be calculated where BS is taken that is for first two rows…

Q: ree of static indeterminac

A: Given:- Beam To find:- degree of static indeterminacy

Q: 200h sooN 200N 3m 3m 'R, "y at point C

A:

Q: 14 MPа Using Mohr's circle, determine the stresses acting on an element oriented at a…

A:

Q: Given stadia interval (I) = 5.42 Zenith angle = 83°-15'-30" What is the Difference in Elevation (V)?…

A: Given data:- The given zenith angle, =83°15'30'' The given stadia interval is, I=5.42

Q: 6) Determine the magnitude of the maximum shear force on the inclined member. 7) Determine the…

A:

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.