Problem no. 2. A wheel of carries a load of 1000kg, as shown in figure. a. Determine the horizontal force P applied at the center which is necessary to start the wheel over a 5m. block. Also find the reaction at the block. b. If the force P may be inclined at any angle with the horizontal, determine the minimum value of P to start the wheel over the block; the angle P makes with the horizontal; and the reaction at the block. 7m 5m P 10m

Problem no. 2. A wheel of carries a load of 1000kg, as shown in figure. a. Determine the horizontal force P applied at the center which is necessary to start the wheel over a 5m. block. Also find the reaction at the block. b. If the force P may be inclined at any angle with the horizontal, determine the minimum value of P to start the wheel over the block; the angle P makes with the horizontal; and the reaction at the block. 7m 5m P 10m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the reactions at the supports of the beam which is loaded as shown. Answers Ax Ay 830 N/m By = A 5.3 m N N N OB 1.7 1.7 m m 290 N/m
Solve on white paper correctly
205 305 285 265 215 315 335
Determine the reactions at the supports of the beam which is loaded as shown. Answers Ax Ay 830 N/m By = A 5.3 m N N N OB 1.7 1.7 m m 290 N/m
A rod system is loaded vertically. There is a simple support at A and a roll support at B. All rods are made of same material and have the same cross-sectional area. |P C 0.5 m 0.64 m А B 0.8 m Construct the work and energy equation for the system where the rods are supposed to be linear springs and the spring coefficient is k=EA/L. Find the vertical displacement of C.
The jib crane is designed for a maximum capacity of 9 KN, and its uniform I-beam has a mass of 240 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 4.3 m. On the same set of axes, plot the x- and y- components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (a) What is the value of R when x = 0.8 m? (b) What is the value of R when x = 3.5 m? (c) Determine the minimum value of R and the corresponding value of x. (d) For what value of R should the pin at A be designed? 9 KN 1.6 m Questions: (a) If x= 0.8 m, R = KN (b) If x= 3.5 m, R= i KN m (c) The minimum value for R = i (d) The pin should be designed to hold -2.9 m i kN at x = kN. i
For a figure shown, a. Draw the influence for reaction at A. b. Draw the influence for Shear At C c. Draw the influence for moment At C. d. Determine the maximum values of these functions for a moving uniform distributed load of 5KN/m. ( Show complete solution.)
Show your complete solution.
Please show complete solutions. Considering EI is constant and the value of P is 425kN, calculate the following using Conjugate beam method : A. What is the value of the reaction at point B in the real beam? B. What is the value of the reaction at Point A in the conjugate beam? C. DISPLACEMENT AT C. D. DETERMINE SA SLOPE AT B.
Section A A solid shaft is firmly held at both ends and carries two comparatively thin disks, as shown in Figure 1. The left-hand disc carries a torque of 12x10³ N.mm while the other carries a torque of 18x10³ N.mm in the same direction. The diameters of the shafts are also shown in Figure 1. Determine the following: the rotation of each disc, (ii) the reaction torques at the ends of the shaft, and the internal torque and maximum sheer stress in the left-hand portion of the shaft. The shaft material has a modulus of rigidity of 70x10³ N/mm². 12x10³ N.mm 18x10³ N.mm Ø 30 mm 1. (a) 210 mm Ø25 mm 480 mm Figure 1 Ø 35 mm 210 mm
A beam supported on three reactions as shown in the figure consists of two segments joined at a frictionless hinge at which the bending moment is zero. Draw the shear & moment diagrams using the a) Area Method, and b) V & M equations. (Hint: Use the hinge to separate portions of the beams by making Free Body Diagrams to enable you to solve for the reactions.) R A 2 20 kN/m 40 KN 4 m B R C 1 hinge V H 1 6 m 20 kN/m R E E
Schematic diagram of a one degree of freedom bridge that can be opened and closed as follows.shown. The weight of the bridge is given as = −??⃗. Using the Virtuel (Virtual) Works method,Find the value of the counterweight Q so that the bridge can stabilize at a given position with the angle. ?⃗⃗⃗ =−??⃗ ‘dir. Also, state the effect of the value of on the equilibrium condition.