Problem 8 A Z₁ = 300 n transmission line is to be serially connected to a 3-m long, Zo = 150-2 line terminated with a 150 resistor. Both lines are lossless, operating at 50 MHz. The phase velocity of the signal on both lines is the speed of light in vacuum. Determine (a) the input impedance of the 3-m long line (b) the voltage standing-wave ratio on the 300-2 line , and (c) the characteristic impedance of a quarter-wave transformer to be inserted between the two lines in order to achieve no reflection on the 300-2 line.

Problem 8 A Z₁ = 300 n transmission line is to be serially connected to a 3-m long, Zo = 150-2 line terminated with a 150 resistor. Both lines are lossless, operating at 50 MHz. The phase velocity of the signal on both lines is the speed of light in vacuum. Determine (a) the input impedance of the 3-m long line (b) the voltage standing-wave ratio on the 300-2 line , and (c) the characteristic impedance of a quarter-wave transformer to be inserted between the two lines in order to achieve no reflection on the 300-2 line.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The standing wave on a transmission line is caused by: Select one: a. The interference between Vt and b. The interference between V(z) and Vt. c. The interference between V and d. The interference between V(z) and Vo. e. The interference between Vt and O f. The interference between V and I. g. The interference between V(z) and h. The interference between V(2) and
I Need the answer fastTable Provided if needed
Electrical Engineering A losless line assumed to be infinitely long and of unknown characteristic impedance Z,, when connected to a lossless line of characteristic impedance 10092, produces a standing wave ratio of value 2 in the 1002 line. The same line (of unknown impedance) when connected to a line with the characteristic impedance 202 produces a standing wave ratio of value 2.5 in the 2012 line. Find: 1) possible values of the reflection coefficient from the connection between the 10092 and Z, lines; 2) possible values of the reflection coefficient from the connection between the 20 and Z.
In a non-resonant transmission line, the reflection coefficient is equal to: a. infinite b. 1 c. 0 d. -1 An open line means that the: a. line can be used at any frequency b. input is open circuit c. termination is open circuit d. line has an air insulator It is the ratio of the load power to the incident power. a. return loss b. mismatch loss c. reflection coefficient d. propagation constant
Question 7 A Full explain this question very fast solution sent me
A lossless transmission line (TL) has a characteristic impedance of Zo= 250 N, a load impedance of ZR = 125 – j150 N and its operating frequency is fo Smith chart to evaluate the following parameters: 150 MHz. Use 1) The load admittance YR. 2) The reflection coefficient [Kr|ZOR 3) The voltage standing wave ratio (VSWR). Then calculate the maximum and minimum impedance in this TL, (Zmax and Zmin). 4) The distance from load to the nearest maximum (dmax) and minimum voltage positions (dmin) (in meter). 5) Find Zd at a distance away from a load by d= 3.3 2. Then calculate Zd using TL equation.
Please do it as quick you can
Microwave
A lossless transmission line (TL) has a characteristic impedance of Zo= 250 2, a load impedance of ZR = 125 - j150 2 and its operating frequency is fo = 150 MHz. Use Smith chart to evaluate the following parameters: 1) The load admittance YR. 2) The reflection coefficient |KR|Z0R 3) The voltage standing wave ratio (VSWR). Then calculate the maximum and minimum impedance in this TL, (Zmax and Zmin). 4) The distance from load to the nearest maximum (dmax) and minimum voltage positions (dmin) (in meter). 5) Find Zd at a distance away from a load by d= 3.3 2. Then calculate Zd using TL equation. %3D 1244 d ENG O Type here to search
A 752 lossless transmission line is terminated with a load impedance equals to 105-jl1502. The length of the line is 0.35 r, use a smith chart to calculate: 1. The reflection coefficient at the load (magnitude and angle). 2. SWR, Zmaxy, Zmin, and the load admittance. 3. The input impedance of the TL. 4. The impedance as seen from a distance d=0.26 ^ from the load.
Solve it plz
1. It is desired to match an 80 2 load to a 50 2 transmission line. Calculate: The value of a single resistor that can accomplish this over all frequencies. The values of two lossless (reactive) components that can accomplish this at a frequency of 400 MHz. The characteristic impedance of a quarter-wavelength transformer that can accomplish this at a given frequency.