Problem 8 3-13. A bar having a length of 5 in. and cross-sectional area of 0.7 in² is subjected to an axial force of 8000 lb. If the bar stretches 0.002 in., determine the modulus of elasticity of the material. The material has linear-elastic behavior. 8000 lb 5 in.- 8000 It

Problem 8 3-13. A bar having a length of 5 in. and cross-sectional area of 0.7 in² is subjected to an axial force of 8000 lb. If the bar stretches 0.002 in., determine the modulus of elasticity of the material. The material has linear-elastic behavior. 8000 lb 5 in.- 8000 It

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Related questions

Q: 1.10 Link BD consists of a single bar 1 in. wide and in. thick. Knowing that each pin has a -in.…

Q: What pressure should be applied to a lead block to reduce its volume by 10% (Bulk modulus of lead =…

A: A lead block has to be under pressure in order to have its volume reduced by 10%..

Q: 3. A plastic tubing has a modulus of elasticity of 50 Pascal. What is the amount of strain was…

A: Given: The modulus of elasticity of material is 50 Pascal. The stress on the material is…

Q: Solve the following problems: A mass of 100 kg moves in an acceleration of 10m/sec". Calculate the…

Q: What is the modulus of elasticity? a) Ratio of elongation of a material to the original length b) It…

A: When a force is applied in a particular area, the modulus of elasticity measures the object's…

Q: 2. A rock sample 1m long and of 2 mm diameter is stretched by a load of 40 kg. If the modulus of…

A: Dear student The modulus of elasticity is expressed as: Y = Stress/ Strain Here, Stress is given by-…

Q: 4. A 5.0 inches cube chiffon cake on a table was exposed to a shearing force of 0.20 The upper…

A: Given-The shear modulus of the cake is G=0.05 lb/in2Slide of chiffon l=5 inchesShearing force…

Q: Assume a hand has a 1.4m shaft of bone with an average cross-sectional area of 3 [cm] ^2. What is…

Q: A wooden dowel is subjected to a shearing force of 715N on its top cylindrical face. If the dowel…

A: Shearing force F=715 N, diameter of dowel d=3cm (radius r=1.5cm), height of dowel h=11 cm and shear…

Q: A steel bar is 10 mm in diameter and 2 m long. It is stretched with a force of 20 kN. Calculate the…

A: Given data: Diameter (d) = 10 mm = 0.010 m Length = 2 m Force (F) = 20 kN = 20 × 103 N Required: The…

Q: 1. A piece of 180mm long by 30mm square is in compression under a load of 90kN as shown in the…

Q: Determine the outside diameter of a tube if the stress is limited to 128 MN/m2 and a hollow steel…

Q: 2. The breaking stress of copper is 210 MPa. What is the maximum force that can be applied to a…

A: Given, Breaking the stress of copper, σb=210MPaσb=210×106Pa Diameter, d=1mmd=1×10-3m The braking…

Q: A disk between vertebrae in the spine is subjected to a shearing force of 825 N. Find its shear…

A: The expression for the shear modulus is, S=FL0A∆x

Q: A liquid compressed in a container has a volume of 2 liters at a pressure of2MPa and a volume of…

A: Elasticity is the elongation or stretch of a material when a force is applied in the discipline of…

Q: 1-66. Determine the largest load P that can be applied to the frame without causing either the…

Q: What is the area of the stock file if a 1.5 x 105 kg mass presses down 2.5 feet high stock file that…

A: Given that-Mass, m=1.5 × 105 kgDeformatio, ∆x= 2.7 cm=2.7×10-2 m=0.027 mHeight, h= 2.5 ft=2.5×0.3048…

Q: A copper wire of length 5.9 m , cross sectional area 2.6 x 10-6m2and Young’s modulus 11 x 1010 N/m2…

Q: A tensile stress is to be applied along the axis of a cylindrical brass rod with diameter of 15 mm.…

A: The lateral strain is, εx=∆dd0 =-3.5×10-215×10-3 =-2.33 The axial strain is, εz=-εxν…

Q: 2. Two metal bars, one steel and the other brass, are bonded at their ends to form a compound bar…

A: Solution:-Given thatEsteel=185 GN/m2EBrass=83.6 GN/m2Asteel=2×ABrassstress in brass bar…

Q: One end of a wire 2 m long and 02 cm in cross-section is fixed in a ceiling and a load of 4:8 kg is…

Q: What pressure is required to reduce the volume of a lead block by 1% ? (Given : Bulk modulus of lead…

A: Description : In this question we have to find the pressure required to reduce the volume of lead by…

Q: Young's modulus for compression of human bone is approximately 9x10⁹ N/m^2. Assume that a femur has…

A: Given in question : Young's modulus (Y) = 9 x 109 N/m2 Stress (S) = 7.5 x 107 N/m2 Length of the…

Q: A wire of length 2m and cross sectional area 104 m² is stretched by a load 102kg the steel wire is…

A: We have to compute here,(a) Longitudinal stress(b) Longitudinal strain(c) Young's modulusWe have…

Q: What will be the shear stress value?

A: Apply Hooke law of elasticity

Q: 2. A 4.0 m long copper wire of cross-sectional area 2 2 cm is stretched by a force of 4.8 x 10° N.…

Q: 1. A wire of radius 0.8 mm and length of 2.5m is stretched by a force of 49N. calculate the stress,…

Q: Question 15 Within elastic limit, the shear stress is proportional to shear strain. What is the…

Q: Each section of the sky way is 1.7 km long, and each segment has a cross-sectional area of 117.4 m2.…

A: In this case, the length of each section of the skyway is given. And each has some cross-sectional…

Q: A cast iron rod of diameter 18 mm and length of 240 mm is subjected to a tensile load of 100 kN, and…

A: Given. T = 100KN = 100,000 N D = 18mm = 0.018 m L = 240mm = 0.24m ∆L = 0.0006 m

Q: a. ML-1T-2 b. ML2T-2 c. MLT-2 d. MLT-1 e. ML-1T-

A: The process of parallel layers sliding past each other is known as shearing. A pile of papers, a…

Q: The compound bar is composed of brass and copper. It supports the axial loads shown below. Determine…

A: Given: Here are the given data, Brass, d=6.5 inches Copper, d=4.5 inches Fbr=450 lbFco=250 lb To…

Q: A hollow metal post is 10 ft long, and the cross-sectional area of the material is 2.5in² . When a…

A: Stress is defined as the force per unit area. Strain is defined as the ratio of change in…

Q: A steel beam is placed vertically in the basement of a building to keep the floor above from…

Q: 3. An aluminum rod is 250 mm long with a diameter of 25 mm before a 165-kN load is applied as shown…

A: Step 1: Step 2: Step 3: Step 4:

Q: A sphere of copper has a radius of 8.00 cm and is compressed uniformly by a force of 5.00 × 108 N.…

Q: Question 28 -4 The shear modulus of aluminum is 2.40x10¹0 N/m².. An aluminum nail of radius 7.51x10…

Concept explainers

Mechanical Properties of Solids

There are three types of matter- solid, liquid and gas. Out of them, solids have a rigid shaped and size. The intermolecular forces of attractions in solids are greatest. Mechanical properties are the physical properties of a material which it shows, when it is provided with certain amount of force or load. These properties are to be kept in mind for various purposes. When a force is applied to an object, the object may or may not get deformed depending upon its elastic property. But every time the object develops a restoring force against the force applied. This is commonly known as stress. If the object changes its dimensions due to the force applied it develops strain ( which is the ratio of change in dimension to the original dimension).

Question

Problem 8
3-13. A bar having a length of 5 in. and cross-sectional
area of 0.7 in² is subjected to an axial force of 8000 lb. If the
bar stretches 0.002 in., determine the modulus of elasticity
of the material. The material has linear-elastic behavior.
8000 lb
5 in-
8000 lb

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Solution

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 8 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

A 195-kg load is hung on a wire of length of 3.80 m, cross-sectional area 2.00 10-5 m2, and Young's modulus 8.00 1010 N/m2. What is its increase in length? ______mm
19. A force of 5000N is applied outwardly to each end of a 5.0-m long rod with a radius of 34.0 cm and a Young's modulus of 1.25 x 10°8 N/m^2. The elongation of the rod is: * A. 0.0020mm B. 0.0040mm C. 0.14mm D. 0.55mm O E. 1.42mm
1. Consider the brass alloy for which the stress-strain behavior is a cylindrical specimen of this material 10.0 mm in diameter and 101.6 mm long is pulled in tension with a force of 10,000 N. If modulus of elasticity is 85 GPa compute the specimen elongation
2. A bar having a length of 125mm and a cross-sectional area of 437.5mm² is subjected to an axial force of 40kN. The modulus of elasticity of the material is 200GPa. The material has linear- elastic behavior. Determine the deformation of the bar. 40 KN 125 mm 40 KN
A copper wire of length 4.4 m , cross sectional area 2.8 x 10--m²and Young's modulus 11 x 1010 N/m² has a 386 kg load hung on it. What is its increase in length? (g = 9.8 m/s²) 4 pts Question 16 esc %23 13 3 4 R Y K D F ock
a cable has a diameter of 4mm and an original length of 2m.The cable is pulled by a force of 130N.The final length of the cable is 2.02m -calculate the youngs modulus of the cable
A tensile test was conducted on a steel bar. The length of the bar was 10 cm and the extension was 2 mm. What will be the % strain produced. Select one: a. 0.02 b. 2 c. 0.002 d. 0.2
4. A support cable on a bridge has an area of cross-section of 0.0085 m² and a length of 35 m. It is made of high tensile steel whose Young's modulus is 2.8 x1011 Pa. The tension in the cable is 720 kN. Calculate the extension of the cable. (10.59 mm] A hollowA cvlinder has lenath 50.0 cm internal diameter 50 cm and eyternal diameter 60 cm
A metal plate has an area of a face 1 m x 1 m and thickness of 1 cm. one face of larger area is fixed and a tangential force is applied to the opposite face. The displacement of the edge cm. Find the produced thereby is 0.005
2
A 785 kg load is hung on a wire of length 8 m, cross-sectional area 0.200 x 104 m2, and Young's modulus 8.00 x 1010 N/m-. What is the increase in its length (in mm)? (Answer in 2 decimal places) A Moving to another question will save this response.
As soon as possible