Problem 6 F1 8 kN S kN/m A couple force acts on the beam. The couple moment at point E is found to be 200KN.m. clockwise. 1. Find the magnitude of F1 & F2. 2. Find the magnitude of the couple force. 3. Find the distance between the couple B. 4m 3m 2m 3m force. F2

Q: Sketch the figure using AutoCAD and hatch the lines with colours . mention the dimesions as shown in…

A:

Q: Determine the value of x and y, 3x + 5jy = 0 O x= 0 , y = 0 O x = 3, y =0 O x = 0,y = 5 O x = 0, y =…

A: Write the given expression. 3x+5jy=0

Q: 8. Write the name of each component (1-19) in the figure selow.

A:

Q: The radial distance measured from the pitch circle of a gear to the top of the gear tooth is known…

A:

Q: cker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in inches

A: A four-bar crank-rocker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in…

Q: able to draw the sequence chart?

A: you are asking about Sequence chart.

Q: Question Completion In the figure below, which of the following represents the dedendum? zeta gamma…

A: Circular pitch is the distance measured from a point on one tooth to the corresponding point on the…

Q: Double acting cylinder cannot be used as a single acting cylinder. Select one: O True O False

A: Single Acting cylinder as it were expands by weight from a pump and after that withdraws by the…

Q: What is the SAE horsepower of an 8-cylinder engine with a bore of 4.556 inches? Round to the nearest…

A: Given data:- no of cylinder (n)=8 bore (d) =4.556 inches To find:-the SAE horsepower

Q: I didn't understand how you fond the angle teta

A: For solution refer below images.

Q: For the bearing shown below in the figure which of the following represents the bearing bore? For…

A: This question is based on the concept of deep groove ball bearing.

Q: L t C Determine the moments at fixed ends 'a' and 'd' ?

A:

Q: A hammer is balanced at the point "A", close to the metal part. If this hammer is then cut along the…

A: Consider the diagram shown below for the hammer with the center of masses for each side.

Q: 4. How many datums are shown on the print? 5. What three symbols are used to describe the small…

A: What there's symbols are used to describe the small hole

Q: Analytically determine the maximum linear displacement of the cutting blade .75 S0 crank blade Your…

A:

Q: Write the following as full (decimal) numbers with standard SI units. b. 10cm c 1001 g d. 48cl

A:

Q: Draw the Venn Diagram and write your answer in set roster notation. 5 pts A={1,2,3,4} B ={1,3,5,7}…

A: Venn diagrams are used to establish relation between things or a finite group of things with the…

Q: The number of teeth on a gear is 27 and the outside diameter is measured as 10 mm. The module of the…

A: Given Data No. of teeth is 27 Outside diamtere is 10mm

Q: solve 4 and 5 only

A: The given state of stress is:To find:(iv) The orientation of the elements for the maximum in-plane…

Q: Two identical cylinders methods cant be used to measure The hand writt Select one: True O False 4

A: Yes, it's true.

Q: SHAFT KEY

A:

Q: Compute the deflection of C after the load removed.

A: Given Conditions :

Q: Number of links? The value must be a number 8 Number of full joints (J1)? Figure 2 Figure 2

A: Given mechanisms,

Q: Which kind of Boolean operation is illustrated in the following figure? Feature 1 Feature 2 Union…

A: Which kind of Boolean operation is illustrated in the following figure? Options :-  Union Subtract…

Q: Determine the sequence for the following figure

A: Given: To find: Sequence

Q: Z is incorrect

A:

Q: What is the radius equivalent to Mohrs Circle?

A: Method to construct Mohr's circle, First Plot point A σx,-τxy, & B σy,τxy on σ - τ plane. Now…

Q: What is the v-velocity at the centerline after refining the mesh

A: To explain: What is the v-velocity at the centerline after refining the mesh.