Problem 4.100 Replace the force system acting on the beam by an equivalent force and couple moment at point B. (Figure 1) Figure 1 y 2 m of 1 2.5 kN 1.5 kN 4 m 30° 3 kN -2m- Part A Determine the magnitude of the resultant force. Express your answer to three significant figures and include the appropriate units. FR = Submit Part B 0 μA Value Submit Units My Answers Give Up Determine the angle between the resultant force and the x axis. Express your answer to three significant figures. IVE ΑΣΦ ↓↑ vec ? My Answers Give Up °, counted counterclockwise from negative axis

Problem 4.100 Replace the force system acting on the beam by an equivalent force and couple moment at point B. (Figure 1) Figure 1 y 2 m of 1 2.5 kN 1.5 kN 4 m 30° 3 kN -2m- Part A Determine the magnitude of the resultant force. Express your answer to three significant figures and include the appropriate units. FR = Submit Part B 0 μA Value Submit Units My Answers Give Up Determine the angle between the resultant force and the x axis. Express your answer to three significant figures. IVE ΑΣΦ ↓↑ vec ? My Answers Give Up °, counted counterclockwise from negative axis

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. PLEASE ANSWER ASAP.
The diameter of rod BC is 40 mm, v = 0.32, G = 78 GPa. Determine the elongation and the decrease in diameter (both in mm) of rod BC after the application of P = 150 kN loads. Note: Draw the Free Body Diagram, include the units/dimensions, use the proper formula and round-off all the answers and final answers to 3 decimal places.
Mechanics of deformable bodies. Two decimal places.
Please solve it quickly ,Urgent.
As shown in this figure are rigid bars supported by rods, what will be the equivalent value of P that can be applied if the maximum vertical displacement allowed is 5mm? ... Aluminum Rod L-2m A-500 mm E= 70 GPa A B Stoel Rod L- 2m A-300 mm E- 200 GPa D P 3m 3m A) 76.4 N B) 78.2 N 82.7 N D) 87.2 N
09:05 A rectangular slab has 4 applied forces, but only F₂ and F3 are known. It is known that the resultant force FR acts through the x, y coordinates (12, 10)m. Variable F2 F3 d₁ d₂ F₁ = F₁ d3 d₁ d5 Value wamap.org Z 12 KN 6 KN 8 m 12 m 4 m 16 m 6m F2 Values for the figure are given in the following table. Note the figure may not be to scale. F3 F4 ) KN d5 y a. Determine the magnitude of the forces F₁ and F4 if the resultant force FR acts through the x, y coordinates (12, 10)m. Round your final answers to 3 significant digits/figures.
Question 1 A brass bar AB projecting from the side of a large machine is loaded at end B by a force P = 6000 N acting with an eccentricity e = 1.14 cm (Figure 1). The bar has a rectangular cross section with height h = 3 cm and width b = 1.5 cm. What is the longest permissible length Lmax of the bar if the deflection at the end is limited to 0.3 cm? (For the brass, use E = 110 GPa.) A Brass bar L Ab Figure 1 B P
The hammer of an impact testing machine weighs 120 lbs. As shown in figure , it is attached to the end of a light rod 5 feet long which is pivoted to a horizontal axis at A.
Must include the free body diagram. Urgent