Problem 4: The loading diagram for a cantilevered beam is shown below. The support at A is fixed. (a) Determine the support reactions at A (b) Determine the shear and bending moment as a function of x, where (0) Oft ≤x≤ 6ft (in) 6ft sxs 10ft Please draw the relevant FBDs (c) Draw the shear and bending moment diagrams for this loading on a separate sheet. (d) Indicate the maximum absolute values of shear and bending moment. Why is it important to know these values? 2k/ft 21/M 10k 10 8k MES 40kft

Problem 4: The loading diagram for a cantilevered beam is shown below. The support at A is fixed. (a) Determine the support reactions at A (b) Determine the shear and bending moment as a function of x, where (0) Oft ≤x≤ 6ft (in) 6ft sxs 10ft Please draw the relevant FBDs (c) Draw the shear and bending moment diagrams for this loading on a separate sheet. (d) Indicate the maximum absolute values of shear and bending moment. Why is it important to know these values? 2k/ft 21/M 10k 10 8k MES 40kft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A plane frame ABCDEFGH shown in figure has clamp support at A, hinge supports at G and H, axial force release (horizontal sleeve) at C and moment release (hinge) at E. The static (D,) and kinematic (D, ) indeterminacies are C B. E F oflot H G
Beam AB is supported as shown in the figure. Tie rod (1) is attached at B and C with double shear pin connections, while the pin at A is attached with a single shear connection. The pins at A, B, and C each have an ultimate shear strength of 57 ksi, and tie rod (1) has a yield strength of 33 ksi. A concentrated load of P = 14 kips is applied to the beam as shown. A factor of safety of 2.4 is required for all components. Determine: (a) the minimum required diameter for tie rod (1). (b) the minimum required diameter for the double shear pins at B and C. (c) the minimum required diameter for the single shear pin at A. 6.7 8 in. 3.8ft (2) 8.5ft
The wooden strut is subjected to the loading shown. Draw the state of stress at point C on an infinite small element. The strut is supported by a bolt (pin) at point B and a roller support at point A. 50N S0N 40N 40 N -60 100 mm 50 mm 25 mm 200 mm 200 mm'200 mm'200 mm 100 mm 100 mm
Link-2, shown in the figure, is 30 mm wide, has 12 mm diameter bearings atthe ends, and is cut from low carbon steel bar having a minimum yield strength of190 MPa. The end-condition constants for link-2 are C = 1 and C = 1.2 for bucklingin and out of the drawing, respectively.a) Draw necessary and clear free-body diagrams to determine the reactions atthe supports and the load on both member-2 and member-3. b) Determine a suitable thickness for link-2, based on a design factor of safetyηD = 4, and considering a material having E = 207 GPa, and a minimum yieldstrength Sy = 350 MPa. c) Determine the stress and resulting factor of safety for each pin, and state yoursuggestions in case of design factors less than 4. Use appropriate (SI) units as it applies (if any.)
A two-dimensional beam structure or frame (ABCD, shown below) has a concentrated load, P, acting on Point D. You can assume that the connections at B and C have sufficient strength to react the applied load and that loads and moments are transferred between the beams. You can assume that the members have a constant cross-section and that El-constant. B A 2m y L. C P-3kN D 2m In order to evaluate the design you must: (a) Sketch the deformed shape of the frame, solve the reaction forces and construct the bending moment diagram for the frame. (b) Use any method to determine the vertical deflection at Point D. Ensure that you clearly explain your approach and show your final answer. Clearly state any assumptions made. (c) If the bending rigidity, El, of the frame between Point B and Point C was doubled. What effect would this have on the resulting horizontal deflection at point D. Ensure that your answer is supported by suitable reasoning, calculations and/or sketches.
e (C) d (mm) P(kN) Q(N) Gallow (MPa) s(%) 20 18 80 12 40 1 (a) The structure shown in Figure Q3 is subjected to two point loads as shown. Determine (i) the axial force in rod BC and the reactions at pin A in terms of P. The value of angle, 0 is given in Table 3. the maximum load, P that can be applied if the average shear stress in each (ii) pin is not allowed to exceed 60 MPa. All pins are subjected to double shear and each has a diameter, d as given in Table Q3. (Hint: Consider only pin A and pin B.) RB 2 m-+-2 m P P Figure Q3 (b) A nylon thread is to be subjected to tension of Q (N). The modulus of elasticity, E of the thread is 3.2 GPa. Determine the required diameter of the thread, if (i) the maximum allowable normal stress is as given in Table 3; (ii) the length of the thread must not increase by more than s (%) as given in Table 3
A For the beam loaded as shown in figure, the location of point of contra flexure from the left end is L Wo B
calculate the location of the centroid, the second moments and product of area for the cross- section if; D = 67 mm, B = 41 mm & t = 2.41 mm A L Test beam A Strain gauge W (a) Unsymmetrical cantilever beam with weight applied at the free end and at the "shear centre", so that there is no torsion induced. Section A-A Strain gauge 1 Strain gauge 2 b Strain gauge 3 a B (b) Location of Huggenberger strain gauges From these, calculate the orientation and position of neutral axis for pure bending in the vertical plane (i.e. bending about a horizontal axis).
The beam shown below is supported by a pin at A and a short link BC. Determine the maximum magnitude P of the loads the beam will support if the average shear stress in each pin is not exceed 80 MPa. All pins are in double shear and have a diameter of 18 mm. 2P 2P 1.5
For the cantilever beam with uniformly distributed load shown in Figure 2. Use (bf hf.bw, hw) for the I section from Table 2, determine the following: The maximum shear force in the beam in (kN) . The maximum bending moment in the beam in (kN.m) The area of the section in (mm?) The moment of inertia about the centroidal x axis 5The maximum shear stress at section I in (MPa) The maximum shear stress at section 2 (within the flange) in (MPa) The maximum shear stress at section 2 (within the web) in (MPa) The maximum shear stress at section 3 (at the neutral axis) in (MPa) The average shear stress on the section (MPa)
An assembly of bars are designed in Figure 1. The assembly is made of structural A-36 steel where bar AB and BC has a drameter of 50 mm. ASTM and 25 mm The respectively. determine дар between C and the rigid wall at D is initially 0-15 mm, the support reaction at A and D when the force P= 292 kN is applied at B 600mm 450mm 292- A B D
A rigid bar BCD is connected by link at AC at point C as shown in the figure. The Structure is supported by bolts at A and B that are in the single shear. The bar is loaded by 4kn at point D. Determine the minimum diameter of the bolt at B if the allowable shear stress is 120 mpA