Problem 4 An open-topped tank with square bottom, 0.9 m on a side is 0.60 m high. It floats in water. A steel block (s=7.86) is placed inside at the bottom center. If the tank alone weighs 300 N, and neglecting the thickness of the walls of the tank, determine (4.a) the maximum allowable weight of steel in KN. (4.b) the draft, in m if the same steel block is now attached at the bottom center outside the tank.

Problem 4 An open-topped tank with square bottom, 0.9 m on a side is 0.60 m high. It floats in water. A steel block (s=7.86) is placed inside at the bottom center. If the tank alone weighs 300 N, and neglecting the thickness of the walls of the tank, determine (4.a) the maximum allowable weight of steel in KN. (4.b) the draft, in m if the same steel block is now attached at the bottom center outside the tank.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

• Problem 14.1. Determine elastic curve of the solid circular shaft. The shaft is made of steel having E = 200 GPa. It has a diameter of 100 mm. M-30kN m 1.5 m 1.5m- R-10KN R3 -10KV
Isosceles triangular gate AB, as shown in the figure, is hinged at A. The horizontal force ( P) is required at point B for equilibrium. The weight of the gate is negligible, and C = 2 m J 5 m E = 1.2 m 9 = 60° %3D S.G. of Oil = 0.82 Oil, SG = 0 82 %3D Gate J
Determine the moment of inertia of the cross-sectional area of the reinforced channel about the x-axis. Assume t = 1.0 in., a = 1.8 in., b = 1.6 in., c = 2.2 in. 一一叫 F₁-a- Answer: lx = i in.4 x
6 m B 60 kN Q 60 KN H P 60 KN 4 panels at 8 m = 32 m EA = constant E Determine the force in member DG. Input your answer as negative if the force is in compression.
2) How large are the reaction forces and bar forces in the given jib? Given: F1 = 20 kN, 5/4 а 5/4 a 1/2 a I F2 = 10 kN , a = 1 m. 2a B A 4а 2a
A vertical cylindrical tank 2 m in diameter and 3.5 m high has two steel hoops with diameter of 12mm, 100 mm from both ends. It contains water to a height of 3 m. Determine: a. Total hydrostatic force b. Tensile stress in each hoop
Determine the vertical movement of the load P Steel L= 4 m A = 300 mm? E = 200 GPa Aluminum L= 3 m A = 500 mm? E = 70 GPa 4.5 m 1.5 m P-100 kN B.
Calculate force F on the gate MN and the position y of c.p specific gravity of oil =0.81 the long of the gate MN = 1m and wide =0.7m
Q.1 -10° I- +20° 8m 26cm EI 5 cross seation 12. m Analyze the above structure for at=30° temperature difference using force methad, draw M diag ram. a=10-5 1/°C
4. Determine the maximum value allowed for the applied force P. Given E = 200 GPa, I = 2x107 mm, the cross-section area A = 4900 mm², and the allowable compression stress Jallowable = 165 MPa. A ہے 6m C 6m B ✈ 6m
4. (a) A cantilever AB of length 1m carries a uniformly distributed load, w kN/m from the fixed end A to the free end B. If the cantilever consists of a horizontal plate of thickness 10mm and with 120mm as shown in the figure below, calculate the total permissible distributed load, w if the maximum bending stress is not exceeding 100 MN/m². Ignore the weight of the Plate. w N/m L. 1m 120mm hine component is subjected to the stresses as shown in the below figure. Using the ho rection AB, inclined at an angle of
Properties: • b1 = 300 mm • b2 = 180 mm • d1 = 250 mm • d2 = 350 mm • f'c = 28 MPa • fy = 414 MPa • eccentricity = 200 mm Determine the following: 1. Location of the plastic centroid measured from the y-axis in mm 2. Depth of the compression block in mm 3. Nominal Axial in kN 4. Moment Capacity in kN-m