PROBLEM 3.52 A 4 kNm torque T is applied at end A of the composite shaft shown. Knowing that the shear modulus is 77 GPa for the steel and 27 GPa for the aluminium, determine (a) the maximum shear stress in the steel core, (b) the maximum shear stress in the aluminium jacket, and (c) the angle of twist at A. [Ans. (a) 73.6 MPa (b) 34.4 MPa (c) 5.07°] 72 mm b 54 mm Steel core 2.5 m Aluminium jacket Fig. P3.52 and P3.53 22:37 14/04/2022

PROBLEM 3.52 A 4 kNm torque T is applied at end A of the composite shaft shown. Knowing that the shear modulus is 77 GPa for the steel and 27 GPa for the aluminium, determine (a) the maximum shear stress in the steel core, (b) the maximum shear stress in the aluminium jacket, and (c) the angle of twist at A. [Ans. (a) 73.6 MPa (b) 34.4 MPa (c) 5.07°] 72 mm b 54 mm Steel core 2.5 m Aluminium jacket Fig. P3.52 and P3.53 22:37 14/04/2022

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A torque T = 40 kip-in. is applied at end A of the composite shaft shown. Knowing that the modulus of rigidity is 11.2 × 10⁰ psi for steel and 4 × 106 psi for aluminum, determine (a) the maximum shearing stress in the steel core, (b) the maximum stress in the alu- minum shell, (c) the angle of twist at A. 2-in. A Steel Aluminum 3 in. 100 in. B
30 mm PROBLEM 3.36 30 mm The torques shown are exerted on pulleys B, C, and D. Knowing that the entire shaft is made of steel (G = 27 GPa), determine the angle of twist between (a) C and B, (b) D and B. 400 N. m 36 mm 900 N- m 36 mm 500 N- m u 90. 0.8 m 1 m 0.5 m PBC = 8.54° PBD = 2.11° %3D
The composite shaft shown consists of a 0.2-in.-thick brass jacket (Gbrass= 5.6 × 106 psi) bonded to a 1.2-in.-diameter steel core (Gsteel=11.2 × 106 psi). Knowing that the shaft is being subjected to the torques shown, determine the largest angle through which it can be twisted if the following allowable stresses are not to be exceeded: τsteel=15 ksi and τbrass= 8 ksi.
A torque of magnitude T= 4 kN·m is applied at end A of the compos-ite shaft shown. Knowing that the modulus of rigidity is 77 GPa for the steel and 27 GPa for the aluminum, determine (a) the maximum shearing stress in the steel core, (b) the maximum shearing stress in the aluminum jacket, (c) the angle of twist at A.
1. A steel shaft is to be manufactured either as a solid circular or as circular tube. The shaft is required to transmit a torque of 1200 Nm without exceeding an allowable shear stress of 40 MPa, nor an allowable rate of twist of 0.75º/m. For G = 78GPa, determine: a. The required diameter do of the solid shaft.b. The required outer diameter d2 of the hollow shaft if the thickness t of the shaft is specified as one-tenth of the outer diameter.c. The ratio of diameters (that is, the ratio d2/do and the ratio of the weights of the hollow and solid shafts.
I at nd. end 3.8 Attaching a hollow shaft to a solid shaft creates the steel shaft. Determine the maximum torque T that may be applied to the ends of the shaft in the 3.5-m length without exceeding a shear stress of 70 MPa or a twist angle of 2.5°. For steel, use G = 83 GPa. =12 T 120mm Alvern de ww08 1914 90 ****************** 2.5m 2007 099 wwg/ 1.8m O
The composite shaft shown consists of a 0.2-in.-thick brass jacket (Gbrass= 5.6 × 106 psi) bonded to a 1.2-in.-diameter steel core (Gsteel=11.2 × 106 psi). Knowing that the shaft is subjected to a 5-kip·in. torque, determine (a) the maximum shearing stress in the steel core, (b) the angle of twist of B relative to end A
3. Two solid 1.75 in.-diameter steel shafts are connected by the gears shown. The shaft lengths are L₁= 6 ft and L2 = 10 ft. Assume that the shear modulus of both shafts is G= 12,000 ksi and that the bearings shown allow free rotation of the shafts. If the torque applied at gear D is TD= 225 lb-ft, determine (a) the internal torques T₁ and 72 in the two shafts. (b) the angles of twist 1 and 2. (c) the rotation angles 3 and þc of gears B and G. (d) the rotation angle of gear D. 4₁ (1) 30 teeth 54 teeth B (2)
A composite shaft is made by slipping a bronze tube of 3-in. outer diameteran -in. inner diameter over a solid steel shaft of the same length and 2-in.-diameter. The two components are then fastened rigidly together at their ends. What is the largest torque that can be carried by the composite shaft if the working shear stresses are 8 ksi for bronze and 12 ksi for the steel? For bronze, G = 6 x 106 psi, and for steel, G = 12 x 106 psi
3.36 The torques shown are exerted on pulleys B, C, and D. Knowing that the entire shaft is made of aluminum (G = 27 GPa), deter- mine the angle of twist between (a) C and B, (b) D and B. 30 mm 30 mm 400 N- m GG 36 mm 900 N- m 36 mm 500 N. m B "0.6 m E. 0.5 m D m 0.5 Fig. P3.36
1. The aluminium rod AB is bonded to the brass rod BD. Knowing that portion CD of the brass rod is hollow and has an inner diameter of 40 mm, determine the angle of twist at A. Take GAL = 27 GPa and GBr = 39 GPa respectively. 60 mm T = 1600 N - m 36 mm T = S00 N. m 250 mm 375 mm 400 mm Figure Q4.1: Compound shaft
3.46 The electric motor exerts a torque of 800 N · m on the steel shaft ABCD when it is rotating at a constant speed. Design specifications require that the diameter of the shaft be uniform from A to D and that the angle of twist between A and D not exceed 1.5°. Knowing that Tmas s 60 MPa and G = 77 GPa, determine the minimum diameter shaft that can be used. 300 N- m 500 N- m 04 m 0.6 m 0.3 m Fig. P3.46