Problem 3The beam is constructed from three boards. It is subjected to a shear of V = 6 kip. Each nail can support a shear force of 550 lb.Part ADetermine the maximum allowable spacing s of the nails used to hold the top flange to the web.Express your answer in inches to three significant figures.ANSWER:St =Part Bin.Determine the maximum allowable spacing s of the nails used to hold the bottom flange to the web.Express your answer in inches to three significant figures.ANSWER:Sb =in.10 in.6 in.1.5 in.HL12 in.1 in.1.5 in.

Answered: Image /qna-images/answer/7b31de7a-18d5-44c7-9879-9e5d1a54460b.jpg

Answered: Problem 3 The beam is constructed from…

Problem 3 The beam is constructed from three boards. It is su Part A Determine the maximum allowable spacing s c Express your answer in inches to three sign ANSWER:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Consider a two-dimensional problem. The stress transformation formulae are then. in full, cos 8-sin…

A: The stress transformation formulas for a two-dimensional problem are:σ'x = σx cos2(θ) + 2τxy sin(θ)…

Q: t, the moment developed at fixed end is

Q: 2. The cantilever retaining wall resists active lateral earth pressure throughout its length. Given:…

A: Retaining walls are used to support soil laterally to retain it at different levels or of poor…

Q: An asphalt pavement drains into a rectangular concrete channel. The catchment surface has an average…

A: Average of the slope of asphalt surface, Distance between catchment boundary and drain, Length of…

Q: A road with 4.5% upward grade has a design speed of 90kmph, if coefficient of longitudinal friction…

A: To determine the sight distance ,Sight Distance = (V2/2g * f) + (V * t)where:V = Design speed = 90…

Q: Following data are obtained in a shrinkage limit test: Volume of saturated soil = 10 cc Water…

A: Given data - Volume of saturated soil = 10 ccWater content of saturated soil = 55%Soil is dried upto…

Q: depth of 600mm and total depth of 650mm. It is reinforced with 4-32mm diameter bars for tension. fc'…

A: Width of the reinforced concrete beam (b): 300 mmEffective depth of the beam (d): 600…

Q: A construction Equipment has a useful life of 6 years after which it has to be replaced by a new…

A: Given Interest rate 6%Useful life 6 yrsTo find out Sinking fund factor

Q: of the following statements is true regarding stopping the work on a project? Check all that apply.…

A: Above conditions are regarding stop work order.

Q: Problem 3 Liquid in a round tank is draining out a round pipe. The term 1) -V() 2) - Vn() 3) -Vπ ()²…

A: dh/dt=??We used here V1 = Velocity at exit = V V2 = Velocity at top of water surface According to…

Q: Ex 2-2: A cylinder of 232 cm² cross section area was used to take undisturbed soil sample of 30.5 cm…

A: A = 232 cm2 h = 30.5 cm Wwet = 114 NWd = 96 N

Q: . . . From the following measured angles, calculate the adjusted angles according to the weight of…

Q: For the 3-reservoir system shown, determine the discharge flowing towards reservoir C, the discharge…

A: Discharge in pipe 1:Using the Darcy-Weisbach equation,Q1 = √(8g * (EL1 - EL2) / (fL1 / D15))where:Q1…

Q: a) Determine the force in member BC of the truss and state if this member is in tension or…

Q: Which among the following air pollutant is not present in an auto exhaust gas NOX CO CO₂…

A: This question is related to the Air pollution from Environment Engineering from Civil…

Q: Using Three Moment Equation, determine all the reactions of the given beams. EI is constant

A: A continuous fixed beam is fixed at both ends and is loaded with 2-point loads on one span and with…

Q: Consider the beam and loading shown. NOTE: This is a multi-part question. Once an answer is…

Q: Two non-slender braces (A and B) resist lateral load in a story of a braced frame. The lateral…

A: This distinctive property prompts an analysis of various aspects of axial forces and their…

Q: For this diagram of an industrial pressure washer system, x = 2 ft, y = 5 ft, z = 9 ft, Q = 3.4…

A: Given data - Q = 3.4 ft³/s dh = 1 in dn = 3 in hL = 4 ft Find out - Pressure at point 2.

Q: rnal pin) pent 3' p lok.ft B5 с F I al Sek F 2k/ft 44²+4²-9 8 ft 6ft, 6ft +4 + E # It K 3.3 ttt off…

A: Given data, fig is givenFINDreactions at the supports

Q: ES Dur LS EF FF TF LF 4. Construct an activity-on-branch network from the precedence relationships…

A: To determine the slack for each task and the critical path, we can use the forward and backward…

Q: The beam is constructed from two boards fastened together at the top and bottom with three rows of…

A: Spacing (S) = 8 in F = 300 lb/nail

Q: A steel column carries an axial load of 787 kN and a moment of 69 kN-m at the top and moment at the…

A: Area of section, Radius of gyration about x axis, Radius of gyration about y axis, Effective length…

Q: P1=P2= 3 kN find all member forces and state whether compression or tension .

Q: Analyze the beam shown below and draw S.F.D and B.M.D. A A E 30 kN-m B x3m 3m² 40KN F с 2 40KN *2mx

Q: 2 m D A 1.5 m B -1.5 m 0.3 m C E 12 kN Determine the horizontal and vertical components of force at…

A: Determine the horizontal and vertical reaction at pin A and D.

Q: H.W. 2: Analyze the compound beam shown below with internal hinge at E and F. a. Check stability and…

Q: determine the distances x and y for equilibrium if f1=800 N and f2=1000N. (Hand written and clean…

A: Given data - F1 = 800 NF2 = 1000 N Find out - Distance x and y ?

Q: The reaction at the support D of the continuous beam ABCD, hinged at two points shown in below…

Q: A rectangular swimming pool has a length of 35 meters, a width of 10 meters, and is filled with…

Q: The wood beam has an allowable shear stress of Tallow 3.5 MPa. 50 mm 4 Part A 200 mm 50 mm 4 50 mm +…

A: Given:Allowable shear stress = 3.5 MPaRequired:Maximum shear force V

Q: According to AS 1726, specify the symbols and generic names used for coarse,medium and fine grain…

A: In AS 1726, which is an Australian Standard, sands are classified based on their grain size using…

Q: Consider the T-beam section below. The beam will not be subjected to any axial loads. The design…

Q: The reaction at the support D of the continuous beam ABCD

Q: 10 kNm 0.9 kN/m 2.5 KN 0.9 KNim 22 kN/m

A: Concentrated moment acting on Beam ,UDl acting on the beam ,

Q: Problem 5: Snowmobiles, Ice, and Water What is the minimum speed to avoid sinking when using a…

Q: Water (60°F) is running through Schedule-80 PVC pipe whose size changes gradually from 6-in nominal…

A: To solve this problem, we can use the Bernoulli equation, P + 1/2 * ρ * v² + ρ * g * z =…

Q: What is the significance of a Soil’s Index Properties? Briefly explain the process of calculating…

A: Soil's index properties and its water content are fundamental and using these index properties can…

Q: 1) 6 ft TITI 1.2 k/ft 18 ft 17 k B Beam Reactions 450 8 ft

A: A simply supported double side overhang beam is shown in the above figure. We have to find out the…

Q: Consider a catchment that has a runoff coefficient of 0.82, an average slope of 0.02, a Manning's n…

Q: A pumping machine in the water lifting station is found to produce a sound level of 50 dB. During…

Q: A 2-foot square footing has its bottom 2.98 ft. below the ground surface. The ground water table is…

Q: using

Q: Calculate the discharge through a trapezoidal channel with a width of 6 m and side slope of 1…

A: Given data - B = 6 m y = 3 m n = 0.003 m = 1:3 S = 1/5000 Find out - Discharge from trapezoidal…

Q: Can you explain the eqautions and processor for finding the location of the trust on the wall? I am…

Q: The soil of an 21 degree infinite slope is subjected to full depth seepage. The soil properties are…

A: Full depth seepage take place. Determine the limiting depth of slope (Hc).

Q: 1) For the cross section shown, assume it is bending about the z-axis. Disregard the labels of H and…

A: Determine the centroid and moment of inertia about z-axis.

Q: As per NSCP 2015, a minimum shear reinforcement in concrete design shall be provided in all regions…

Q: Is the design adequate? Provide clear and concise (and neatly presented) evidence to support your…

A: A retaining wall is given we need to find out the design is adequate or not.

Q: Of new tyres with good treads and worn-out tyres, which one gives higher friction factors in wet and…

A: We need to choose which type of tyres gives higher friction factor in wet and dry condition…

Question

Problem 3
The beam is constructed from three boards. It is subjected to a shear of V = 6 kip. Each nail can support a shear force of 550 lb.
Part A
Determine the maximum allowable spacing s of the nails used to hold the top flange to the web.
Express your answer in inches to three significant figures.
ANSWER:
St =
Part B
in.
Determine the maximum allowable spacing s of the nails used to hold the bottom flange to the web.
Express your answer in inches to three significant figures.
ANSWER:
Sb =
in.
10 in.
6 in.
1.5 in.
HL
12 in.
1 in.
1.5 in.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Determine the maximum allowable spacing of the top and bottom flange to the web

VIEW

Step 2: Determine the maximum allowable spacing of the top and bottom flange to the web

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The piece of wood, 100 mm by 100 mm in cross section, contains a glued joint inclined at the angle y to the vertical. The working stresses are 20 MPa for wood in tension, 8 MPa for glue in tension, and 12 MPa for glue in shear. If y ¼ 50 , determine the largest allowable axial force P.Show FBD of the three stresses
Problem 3: Method of Sections Inputs: ● ● h = 12 ft b = 7 ft F₁ = 2100 lb F₂ = 800 lb 0 = 25° You must use the method of sections as described below. You will not receive credit if you use the method of joints! Take a horizontal section cut through the middle of the truss and keep the top portion for your FBD. That way you don't have to bother with the reactions at A and D. Using the FBD of the top portion of the truss, perform the following steps: F₁ B a) Use EFX = 0 to compute BD. Indicate tension vs. compression. b) Use MD = 0 to compute AB. Indicate tension vs. compression. c) Use [MB = 0 to compute CD. Indicate tension vs. compression. d) Use [Fy = 0 to check all values D F₂
2. A piece of wood was cut into 3 pieces as shown below and will form into a l-beam section. Planks 1 will be the top and bottom flange members while the Plank 2 will be the web member. A sample l-beam is shown below. In addition to that, a steel plate will be installed (at the center) at the bottom of the l-beam to ensure its strength. Calculate the I subscript x with bar on top end subscript (Moment of Inertia with respect to centroidal x-axis) of the built section. b top flange h bot flange 1 1 3b b 3b 8 4 8 tp Wp Given o b = 2.1 cm h = 36 cm tp = 0.55 cm wp = 21 cm 2. web
Q1: For the simply supported beam of the cross sectional dimensions and load shown in the figure, determin 3- The spacing required for nails A and B if they stand a force of 2 kN. S = 1- The max. bending stress in the beam. 2- The max. shear stress in the beam. F Fblt vQ 9 = ON 나오 50 Fail A w= 10 kN m 150 2 m 4 m 150 50 Nail B All dimensions in mm 50 150 50
1. The cast iron block with cross-sectional dimensions of 62.5 mm by 62.5 mm consists of two pieces. The pieces are prevented from sliding along the 55 degrees inclined joint by the steel key, which is 62.5 mm long. The working stresses are 275 MPa for cast iron in bearing and 345 MPa for the Key in shear. If the block is loaded with P = 282 kN, calculate the required dimension "b" of the key. Write your final answer in 2 decimal places with the unit of mm.
Two wooden planks, each 18 mm thick and 250 mm wide, are joined by the glued mortise joint shown. Knowing that the joint will fail when axial load of magnitude P = 19 kN is applied . If length of the cut d = 30mm, determine the maximum average shearing stress. provide your answer in MPa with precision to two decimal points. P Answer: Glue 25 mm 200 mm P 25 mm
The truss supports a F=80.0-kN load at J. The horizontal members are each 1 m in length. Figure 1m ZZ E F G H F 1 of 1
The beam is constructed from three boards. Determine the maximum shear V that it can support if the allowable shear stress for the wood is tallow = 400 psi. What is the maximum allowable spacing s of the nails if each nail can resist a shear force of 400 lb?
Please write the complete solutions and Legibly. Rate will be given! Do not just copy asnwers in CHEGG! Thank you :) A singly reinforced rectangular beam section 250 mm wide, 400 mm deep is reinforced with 2-36-mm-dia. rebars, grade G420 enclosed with 10-mm-dia. stirrups. X Calculate the tensile steel stress when concrete crushes at a strain of 0.003. Use f'c = 21 MPa. Use 3 Decimal Places.
Given a 10"X16" reinforced concrete beam section as shown. The main reinforcing rebars consist of two #6 (each #6 bar has a section area of 0.44 square inches). Concrete fc'=3000 psi. Rebar yield strength fy=60 ksi. What is the section's theoretical nominal bending moment capacity in ft-k? loll O A. 65.8 ft-k. OB. 57.0 ft-k. OC. 34.1 ft-k. OD. 29.7 fft-k. X²N 16"
The beam is constructed from three boards. (Figure 1) The allowable shear stress for the wood is τallow=465 psiτallow=465 psi. Each nail can resist a shear force of 395 lblb. -Determine the maximum loads P that it can support. -What is the maximum allowable spacing ss of the nails used to hold the top flange to the web? (Consider only regions AC and BD.) -What is the maximum allowable spacing ss of the nails used to hold the bottom flange to the web? (Consider only regions AC and BD.)
The 6-inch by 6-inch timber has a unit weight of 38 #/fn and is held in a horizontal position by the concrete anchor. The length, L is 16 feet. Calculate the minimum weight that the concrete anchor must be in order to hold the timber in the horizontal position under water as shown in the figure below. Assume that concrete y 150 #/n³. Hinge timber Concrete anchor a. 84 pounds b.110 pounds O. 146 pounds Od.279 pounds Oe. Problem cannot be solved, not enough information is given