PROBLEM 3: A reinforced concrete cantilever beam is reinforced with 2D28mm dia. top bars. Side, top and bottom cover is 75mm. If fc'=28MPa and fy=280MPA. a. Compute the development length required for the bar teminating in a 180 degree hook b. What should be the minimum inside diameter of the hook?

PROBLEM 3: A reinforced concrete cantilever beam is reinforced with 2D28mm dia. top bars. Side, top and bottom cover is 75mm. If fc'=28MPa and fy=280MPA. a. Compute the development length required for the bar teminating in a 180 degree hook b. What should be the minimum inside diameter of the hook?

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.5.1P

See similar textbooks

Related questions

Q: eam has b = 300 mm and d =490 mm. Concrete compressive strength f′c = 27.6MPa and steel yield…

Q: Aw: Find the slope and deflecion in the section CA-A) aned the Section (B-B) for the beam Shown.…

Q: beam is subjected to a shear of 150 kN. Bel ge width, bf = 200 mm ge thickness, all depth, d = 300…

Q: The short column below is subjected to Pu = 100W kN. . Use f’c = 28 MPa and fy = 415 MPa, Clear…

A: Compression member is a structural member which is primarily subjected to axial compression. If the…

Q: Q2// A 600 × 400mm rectangular tied column shown below support an axial compressive factored load P…

A: Reinforced concrete Reinforced concrete (RC), also known as reinforced cement concrete (RCC), is a…

Q: 1. Compute the vertical distance of link AB from pin E for the given set up if the tension in link…

A: Given:- The magnitude of the weight at GF = 800 lb The magnitude of the tension in link AB = 1500 lb…

Q: Draw the elastic curve of the beam shown. Determine the deflection (indicate upward or downward) at…

A: Reactions in Real Beam: RA+RD=100+20×4+12×4×20RA+RD=220....1…

Q: besign the steel reinforcement op a 400mm x600mm RC beam used to camy a pactored moment,mu-500KN.m.…

A: Using the Limit State method to design the steel reinforcement of the beam, We will design this beam…

Q: Problem 01: Determine the plastic moment capacity of the continuous beam shown. Use a load factor of…

Q: a 5m simple beam ABC carries a uniform load of 78kN/m. point A is the left end hinge support, point…

A: Consider the following figure. For a simply supported beam, the value of the maximum bending moment…

Q: Design and axially loaded short square tied column for Pu = 2,600 kN, if f'c = 28 MPa %3D %3D and fy…

A: Load(Pu)=2600 kN Concrete strength(fc)=28 Mpa Yield strength(fy)=350 Mpa ρ=0.02

Q: A 400 mm x 500 mm rectangular tied column is reinforced with eight D28mm longitudinal bars, four (4)…

A: Given Data: The width of the column is b=400 mm. The depth of the column is D=500 mm. The number of…

Q: Draw the free-body diagram for the following problem.The boom shown.

A: FBD:

Q: Bin? t. Sft lo in 2 20K Bin? Gin? 8 in 2 - 20 ft

Q: Consider the reinforced beam section below with E = 200 GPa, Ec = 22.05 GPa, fsa = 138 MPa and fca…

Q: w kN/m A L/3 ↓ L/3 ↓ L/3 A 9m long simply supported beam shown above, is subjected to a 4 kN/m…

Q: Compute the design moment strength of the beam IPa. d = 650 mm d' = 70 mm b = 450 mm As': 3-28mm…

Q: Wz 118.71mm 25 mm HI 6=45° 1. 下 160mm A W. 200mm 850 mm -950 mm D 200 mm W 1297. 26 N D: 150 mm Wz =…

Q: Determine the force-couple system at O which is equivalent to the two forces applied to the shaft…

Q: a. Determine the ftop at x=8 m from left end. (MPa). b. Determine the fbot at x=8 m from left end…

Q: A C 3m L-6m en El = 10,000 kN-m² he given beam, you can choose Double Integration Method or I Method…

Q: Solve for axial force BF using portal method.

Q: Q3: Find moment at point(A,B,C and * D) P = 800 lb T= 600 Ib 6' C/60° DI 3

Q: non uniform cantilever beam I meter tong. om KN m2

Q: A 20"x30" column with Ag' = 6#6 and Ag = 6#8. If the neutral axis depth3D7", concrete cover (d') = 2…

A: As math type not available, Providing Hand written solution

Q: 1.5 kN 3 kN 2 kN ET F 1.5 m B -1.5 m- -1.5 m-

Q: Determine the theoretical steel areas re rectangular section with b = 350 mm, d moment of 1,500…

Q: Analyze the structure below using cantilever beam method 25KN C 3m 50KN B E. H 4m -6m- 8m- ml

A: Data Given: Asked: Axial load at HI

Q: A rectangular reinforced concrete beam 325 x 550 mm (b x d) is provided with 3H25 bar (As = 1473…

A: Given: b=325mm d=550mm d'=55mm ASC=1473mm2fck=30N/mm2fyk=500N/mm2 Area of steel in tension:…

Q: 250 kN 20 kN/m 교 B 12 m -12 m +4m+4m

A: For analysis of Fixed or Continuous beams, Three Moment Equation Method (Clapeyron’s Theorem) can be…

Q: Consider the continuous beam shown below: 40 kN 6 kN/m 上 A 2EI El 2m 2m 5m Determine the stiffness…

Q: The short column below is subjected to Pu = 1500 kN. . Use f’c = 28 MPa and fy = 415 MPa, Clear…

A: Given, Pu=1000 kN F'c=28 MPaFy=415 MPa Clear cover= 40 mm

Q: Determine bar force members EB, EC, and DC using method of sections. You may not copy the problem. F…

A: To find force in member EB,EC,DC

Q: Problem No. 1A 250x450mm beam with a concrete cover of 40mm and stirrups of 10mm with fc' of 21Mpa…

Q: For the beam section shown below, a) Determine the effective width bef, given the actual flange…

Q: Find deflection at point B (where p load is applied) Without sidesway

Q: Cafe the vertical displacement a Q2:Determine the value of (L) so that at C and B are Load Method ".…

A: In unit load we have to apply a unit load at the point where we have to find deflection.

Q: Draw the elastic curve of the beam shown. Determine the deflection (indicate upward or downward) at…

Q: The 450N plate is attached to collars which may slide on the vertical rod. If the coefficient of…

A: F=200N W=450N a=2.75m b=4.5m c=2m

Q: Design a sliding gate wing type of beams (w8*40) which have an elastic section modulus equal to 582…

A: Solution-The given values are as follows,Beam type-w8×40Elastic section modulus=582cm3Height of…

Q: ACI Code Table 9.7.6.2.2 sets the maximum spacing of vertical stirrups of d/2. Explain why?

A: The required stirrup spacing can be calculated using the formula:-…

Q: Determine the slope at the roller B of the double overhang beam shown. Take E = 200 GPa, I = 18(106)…

A: Calculate the value of the slope at point By using the property of superposition:

Q: What minimum theoretical depth is needed for the 500mm wide beam shown if no torsional reinforcing…

A: Given -

Q: Situation 5. Determine the member forces CD and GF using any method. Indicate if (T) or (C). 2 kN…

Q: The short column below is subjected to Pu = 1325 kN. Use f’c = 28 MPa and fy = 415 MPa, Clear cover…

A: In a short Column if the Buckling and slenderness is disregarded then the moment will occur due to…

Q: For the beam shown, what is the value of the shear diagram just to the right of B? 30 kN 15 kN m-…

Q: DETERMINE BAR FORCE MEMBERS EB, EC, AND DC USING METHOD OF SECTIONS. PLS ADD FBD. 3.2 KN 2.0r D 2.0m…

Q: Given: POST-TENSIONED BEAM with A PARABOLIC TENDON PROFILE Span Length = 20 m fi = 1200 N/mm² A, =…

A: Span length = 20m fi =1200 N/mm²As = 2850 mm²Ac=4.23x105 mm²I = 19.36x1010 mm4e= 560 mm (@ midspan,…

Q: Find the volume of each of the light post ‘s components: a. Concrete Pedestal __________ b. Steel…

A: A street light, also known as a lamppost, street lamp, light standard, or lamp standard, is an…

Q: calculate the depth of neutral axis of a beam of size 450 x 300mm. Use M25 concrete grade and 4 no.s…

A: Consider the free body diagram As per limit state method. IS-456:2000 The diameter of…

Concept explainers

Types and properties of steel

Steel is an alloy of iron. It is formed by heating iron and combining carbon (0.1-1.7%) with it and minor amounts of other elements such sulfur, chromium, manganese, nickel, etc. Thousands of steel grades have been published, registered, or regulated around the world, each with its chemical composition, and special numbering systems have been devised in various countries to classify the vast number of alloys.

Question

PROBLEM 3: A reinforced concrete cantilever beam is reinforced with 2D28mm dia. top
bars. Side, top and bottom cover is 75mm. If fc'=28MPa and fy=280MPA.
a.
Compute the development length required for the bar teminating in a 180
degree hook
b.
What should be the minimum inside diameter of the hook?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

HiW@ Draw S.f.n and BiMin for beam shown by Naphial methds Anst hinge %3D M= 9 W.m 3m 2m 3m Mmny = -6 IW.m
A simply supported beam spans 8 m. It carries the uniformly distributed load throughout of its length. Dead Load, D = 15 kN/m (beam weight not included) %3D Live Load, L = 10.8 kN/m Given: Beam section: W460 x 97 kg/m Area - 12, 320 mm? Depth, d - 465 mm %3D Flange width, bf = 193 mm Web thickness, t = 11 mm !! Flange thickness, t - 19 mm Zx - 1.89 x 106 mm Zy - 2.18 x 10° mm E-200,000 MPa Fy- 345 MPa
1. A steel column 10 m long is fabricated from a cover plate and C section arranged as shown. Determine the safe compressive load. Fy = 248 MPa, E= 200 GPa. Use AISC/NSCP Specs. 450 mm -cover plate 'I 12 mm y2 IP d2 10 m C 310 x 37 A = 4720 mm? d = 305 mm bf = 77 mm tf = 12.7 mm tw = 9.8 mm C 310 X 37 a) Both ends of column are fixed b) Both ends of column are hinged c) One end fixed, the other end hinged Use design values of k. tw d=305- Ix = 59.9x10° mm ly = 1.85x10° mm x = 17.1 mm x=17.1
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with d-20-mm-dismeter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is M0 mm and at the bottom is 70 mm. Use concrete strength r'e-21 MPa und steel yield strength fy 415 MPa for 20- mm bars and fy= 275 MPA for 16 mm bars Detenmine the design moment capacity n kN m of the beam in negative bending. A 40.06 O45.07 C. 42.70 D47.55
Need complete and elaborate solution A.Using ASD, check the adequacy of the base plate (PL400x350x19 mm) centered on a W12X152 column as shown. It is resting on a concrete pedestal that is 450 mm x 400 mm. The loads are PDL = 600kN and PLL = 320 kN. Use A-36 steel and concrete fc’=20 MPa. B. Using LRFD, PL400x350 mm base plate, W12x120 column, 500x500 mm pedestal, PDL = 1200 kN and PLL = 800 kN. Use A-50 steel and concrete fc’ = 30 MPa. Determine the required base plate thickness.
Question 1 Check that the medium-term load of 38 kN applied to the spaced column shown in below complies with the design requirements of BS 5268-2. The column consists of two 38 x 150 C22 timbers 76 mm apart. All joints are glued and intermediate packs are 250 mm long. suitable connection #### x ->89² 6:38. Y T -end blocking AP 100 intermediate blocking L₂ 1₁ x W L W EFH 400 m 38kN medium term load -ICHICHID -200 600 600 600 600 600 600 200 38kN medium term load
Hw: Find the Sslope and defletion in the section CA-A) and the section cB-B) fur the beam Showwn. Given, I = 5*l-"m4 aued Es 205 G Pa. A 2 kulm Im 2.5 m Im A
Problem 01 Using ASD, check the adequacy of the base plate (PL400X350×19 mm) centered on a W12X152 column as shown. It is resting on a concrete pedestal that is 450 mm x 400 mm. The loads are PDL = 600KN and PLL = 320 kN. Use A-36 steel and concrete fc'=20 MPa. TH
H.W A Solid Steel bar of dlameter 6omm and length 350 mm is Placed inside an aluminum cylinder öf Inside diameter Femm and out side d lameter Ilomm, a comPressive load of looo lais applied on the assembly, find the stresses in the bar and the cylinder ? take Est = 200GPa and EAl = F0GPan %3D Cover Plate 0.25mm d- do 35omm A lum. cylinder Steel bar
How Determin # As for the beam show in figre (including self weight) (P=35 M²-i fy=420) well kN/m WL=24 K~/3 590 250 5m
cd efgh ij O klmn u op V 0 0 0 t Р What is the line for which the section will rupture in tension? All holes are the same diameter. m n j h d
A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The beams are spaced at 7 feet 6 inches, and the span length is 30 feet. The superimposed loads are as follows: construction load = 20 psf, partition load = 10 psf, weight of ceiling and light fixtures = 5 psf, and live load = 60 psf, A992 steel is used, and fc=4 ksi. Determine whether the flexural strength is adequate. a. Use LRFD. b. Use ASD.