Problem 3: A hole is to be punched out in a plate that has a shear strength of 40 ksi. The working compressive stress of the punch is 50 ksi. -Compute the maximum thickness of the plate in a hole 2.5 inches in diameter can be punched. -If the plate is 0.25 inch thick, determine the diameter of the smallest hole that can be punched.

Problem 3: A hole is to be punched out in a plate that has a shear strength of 40 ksi. The working compressive stress of the punch is 50 ksi. -Compute the maximum thickness of the plate in a hole 2.5 inches in diameter can be punched. -If the plate is 0.25 inch thick, determine the diameter of the smallest hole that can be punched.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.3P: A tensile test was performed on a metal specimen having a circular cross section with a diameter 0....

See similar textbooks

Similar questions

A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
Shown is a copper bar which has a diameter of 10 mm and loaded by tensile loadP = 0.0137 MN The maximum shear stress in the bar is approximately: Match each item to a choice: Tmax
help me please
The 10-mm-diameter steel bolt in (Figure 1) is surrounded by a bronze sleeve. The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. Est = 200 GPa, Ebr 100 GPa. Figure P P -10 mm -20 mm 1 of 1 Part A If the bolt is subjected to a compressive force of P = 21.9 kN, determine the magnitude of the average normal stress in the steel. Express your answer to three significant figures and include appropriate units. Ost = Submit Part B Obr = Submit 0 Value If the bolt is subjected to a compressive force of P = 21.9 kN, determine the magnitude of the average normal stress in the bronze. Express your answer to three significant figures and include appropriate units. Provide Feedback A Request Answer Value Units Request Answer Units ?
What force is required to punch a 21-mm-diameter hole in a plate that is 23.8 mm thick? The shear strength is 420 MPa. (Answer must be in Newton) ... Puncher d mm ø t mm thick Punched out d mm t mm Round your answer to 2 decimal places. Add your answer
As in the given figure, a hole is to be punched out of a plate having a shearing strength of 40 ksi. The compressive stress in the punch is limited to 50 ksi. (a) Compute the maximum thickness of plate in which a hole 2.5 inches in diameter can be punched. (b) If the plate is 0.25 inch thick, determine the diameter of the smallest hole that can be punched.
A high-strength steel band saw, 24 mm wide, runs over pulleys 800 mm in diameter. What minimum thickness of the steel band can be used without exceeding a flexural stress of 280? Assume E = 230 GPa. Answer must %3D be in mm.
A hole is to be punched through a steel plate of 8 mm thickness. What is the least diameter of hole which can be punched, if the steel punch can be worked to a compressive stress of 800 N/mm² and the ultimate shear strength is 300 N/mm²? A 1.2 mm B 12 mm C 21 mm D 2.1 mm
The axial load 396 kN applied to the lap joint is distributed equally among the three 20.6-mm-diameter rivets. What is the maximum tensile stress (in MPa) in the plate if w = 135.4mm and t = 27.1mm? Round off the final answer to three decimal places.
The two wooden boards shown in the figure are connected by a 0.5 in. diameter bolt. Washers are installed under the head of the bolt and under the nut. The washer dimensions are D  2 in. and d 5/8 in. The nut is tightened to cause a tensile stress of 9,000 psi in the bolt. Determine the bearing stress MPa between the washer and the wood
Two wooden boards are joined by cutting and gluing them together along the plane shownin the illustration. The boards have cross-sectional dimensions of 3.5” by ¾” and are subjectedto an axial tension, P, of 1870 lb.a) Determine the normal and shear stresses acting on the glued joint if  = 20o.b) For what joint angle, , will the shear stress on the glued joint be equal (in magnitude) totwice the normal stress on the joint?
Situation 1: A rigid bar ABC weighs 10 kN/m. The compressive stress of the copper bar is 20 MPa. Answer the following questions: 3m B 2 m Copper L=3m A = 1500 mm² Brass C L = 2 m A = 1200 mm² A. What is the stress of the brass bar? Indicate if it will experience tension (T) or compression (C) (MPa) B. What is the minimum required diameter of the pin at A assuming that the pin connection is in double shear? Consider the allowable shearing stress of the pin as 15 MPa. Round your answer in a multiple of 5. (mm)