2021/04/16 13:06Problem 3- 109iguune tA Dlock of wood having a volume ot 0.034 m and, weighing 300 N issuspended. in water as shown awooden rod of length 3.4 m and cross-sectionof 200 mm? is attached to the weight and also to the wal. If the rod weighs foN determine the angle a for equilibrium,KN/Arist a = 10,50.31 mcient o300 NtorsPatth

Buoyant force: The body immersed in the water will experience buoyant force. The buoyant force is…

Problem 3- 109 10ock of wood having a volume ot 0,034 m² and weighing 300. N is suspended in water as shown awoden rod of length 3.4 m and cross-section of 200 mm² is attached to the weight and also to the wall. If the rod weighs 16 N determine the angle o for equilibrium. Anisa 105° 0.31 m 300 N

Problem 3- 109 10ock of wood having a volume ot 0,034 m² and weighing 300. N is suspended in water as shown awoden rod of length 3.4 m and cross-section of 200 mm² is attached to the weight and also to the wall. If the rod weighs 16 N determine the angle o for equilibrium. Anisa 105° 0.31 m 300 N

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

AIR 4. AIR 1.5 OIL S.Cこ 0.9 FIND THE AIR OF VALUE WA TEN THE RESULTANT FORCE ON WALL ABC WALL Is 2 m WIDE CLE AR, NE AT NEAT FBD R£QUI2EDり PATM = 101. 3k Pa E QS %3D H2D F# = thea A P =th
Plese answer c
Can you solve number two
If the allowable shear strength of the wood is 80 psi, determine the maximum load P that may be applied at midspan.
Observe diagram and dimensions carefully . Give me right solution according to the question.
A rectangular piece of wood, 134.03 mm by 100 mm in cross section, is used as a compression block as shown. Use θ = 29.13°. What will be the value of the axial load P (in kN) if the shear parallel to the grain is limited to 14.88 MPa?
Kindly answer it. Thank you ?
Design the slab of the plan shown below. The dead load is due to self- weight plus weight. of: • Tiles 3 cm mortar 2 cm • sand 7 cm • plaster 2 cm • partition 2kN/m² 10.00 m Live load =2.5 kN/m² fc= 25 MPa and fy= 420 MPa. 0.30 m +0.30 m 0.30 m -4.80 m -3.30 m
The joist AB used in housing construction is to be made from 8-in. by 1.5-in. Southern-pine boards. The design loading on each board is placed as shown in the figure below. The allowable bending stress for the wood is Jallow 1.5 and the allowable shear stress is Tallow = 180 psi. Assume that the beam is simply supported from the walls at A and B. (Figure 1) Figure 1 ▾of 1 8 in. 150 lb L 150 lb L 150 lb L 1.5 in. Determine the largest room width I that the boards can span. Express your answer to three significant figures and include the appropriate units. L = 32.0 Submit μA ft My Answers Give Up ? Incorrect; Try Again; 3 attempts remaining
A wooden joist 15 cm deep by 7.5 cm wide is reinforced by gluing to its lower face a steel strip 7.5 cm wide by 0.3 cm thick. The joist is simply-supported over a span of 3 m and carries a uniformly distributed load of 5000 N. Find the maximum direct stresses in the wood and steel and the maximum shearing stress in the glue. Take Es/Et = 20. (Cambridge) Answer: wood 4.56 MN/m2; steel 52.9 MN/m2; glue 0.21 MN/m2. Show your solution
A simply supported wood beam of length L = 10 ft carries a concentrated load P at midspan, as shown. The cross-sectional dimensions of the beam are b=4 in. and h = 7 in. If the allowable shear strength of the wood is 100 psi, determine the maximum load P that may be applied at midspan. Neglect the effects of the beam's self-weight. A Answer: P = i B lb ہراب y b h
Determine the smallest permissible diameter of the pole. ____________ inches in 2 decimal places.