Problem #2: e = 40 + C (degrees) 650 + Y (N) | 30° B Fy = 800 N 3. Determine the magnitude of the resultant force acting on the ring at O. (N) 4. Determine the direction of the resultant force measured counterclockwise from the positive x axis. (degrees)

Q: steel tension test specimen has a diameter of 6.00 mm and a gage length of 25 mm. The following data…

A: Answer : Data Provided : Diameter  of steel rod = 6 mm Gauge length = 25mm   To calculate : Material…

Q: Problem 1 Determine the magnitude and sense of the couple moment. Given: F = 5 kN 0=30° a=0.5m b=4m…

A: Given Data - F = 5 KN a = 0.5 m b = 4 m c = 2 m d = 1 m Find out -  The Couple Moment ?

Q: Determine the coordinates of the centroid of the area bounded by the curves y = – -x² + 4x - 7 and y…

A:

Q: A steel strip of 30mmx2mm cross section is placed through a row of five pegs. The pegs gave diameter…

A: The given data is as follows: Size of steel strip=30 mm×2 mmDiameter of pegs=12 mmSpace interval…

Q: Im still confused since we didn't end up with the same final values as the photo. Its showing TA =…

A: Given problem related to "calculation regarding torque".

Q: Determine the coordinates of the centroid of the trapezoidal area shown. Assume a = 330 mm, b = 620…

A:

Q: 1. Use the data from the table below to draw the node network. Then do the CPM calculations and…

A:

Q: Solve the matrix X of the equation (B- 2X): %3D |

A:

Q: Consider a triangle with sides 3 cm, 4 cm, and x cm. Let g be the included angles of the sides with…

A: Surveying is the engineering operation that involves calculating and recording details of an area of…

Q: The answer in the book is a=1.67 m

A: From the given question, we have to find out the value of 'a' to consider the same amount of…

Q: Show correct and step by step solutions.

A:

Q: / Find the area of the region that lies inside r =6 sin0 and outside r=2+2sin0

A:

Q: PROBLEM 2: Calculate the components of the forces at B and C. В D E A

A:

Q: Q.2 A uniform, single-span steel beam ABCDE is simply supported at A and E and carries loads as…

A: Find reactions:RA=RB=60+60+40×52=160kNsoDraw moment diagram :iorigin at ALimits…

Q: : Prove that (1) Ya = Gs Yw 1+e

A:

Q: the answer quic

A: Given:- x3-2x-5=0 To find:- positive root

Q: Compute the coordinates of the centroid (,) of the area shown. Also compute the area moment of…

A: Given  To find The coordinate of the centroid is The y coordinate of the centroid is The moment of…

Q: PROBLEM 7 Determine the coordinates of the centroid of the shape given below. y 0.8 m 0.6 m 1.0 m X

A:

Q: PROBLEM The centroid of the T-section shown is 2.9 inches above the base and x is 11. What should be…

A:

Q: Q1 Choose the right values of X which satisfy the following inequalities* a) ->2 |2r+3

A: The detailed solution is...

Q: no.1 asap.

A:

Q: find the second derivative in its simplified form 4. y= e^4x - e^-4x  /  e^4x + e^-4x

A: Consider the given equation y=e4x-e-4xe4x+e-4x Calculate the derivative of given equation…

Q: Find the centroid of the area bounded by a?y = x3, the y axis and y- 8a = 0.

A:

Q: Shear stre Choose the correct answer ss has units:       a. Nt m       e. Viscosity v times area…

A: given data : the units of shear stresss a. Nt m b. Nt m2   c. Nt/m2   d. Nt/m   e.…

Q: Find the value of displacement if force applied is 12 N and work done is 63 i

A: Introduction : The given question is related with mechanics . In this question we are provided with…

Q: A tape 100m long, it's cross sectional area in 0.0585 cm', the apparent length of which was found to…

A: Given that:                     Nominal length of tape, l = 100mArea of cross section, A = 0.0585…

Q: Determine the partial differentiation for each of the following functions (i) z = x²y cos(xy) (ii) z…

A:

Q: Determine the coordinates of the centroid of the trapezoidal area shown. Assume a = 275 mm, b= 485…

A: The given figure is:

Q: R W Problem Statement: The cantilevered round bar in the figure with diameter d = 25 mm, is made…

A: Given:-      Fx=Fy=0                   Fz=1400N          diameter of rod d=25 mm           a=500 mm,…

Q: The following cross section has dimensions as indicated. The length of the right-hand vertical…

A: Draw FBD:

Q: OFind the values of the remaining frigonometric funcfions of o if sec o = - 15, 0 E 3rd quadrant

A:

Q: Setup this problem to solve for x position of the centroid for the parabolic area. Use a vertical…

A:

Q: Determine the x- and y-coordinates of the centroid of the shaded area. Y I Ti 0.34 al TE Answer: (x,…

A:

Q: dy Solve the differential equation of - dx A In y = c Inx B) y = c Inx Cy=lnx + c (D) y^2 = In x + c…

A: Given,dydx=ylnxdyy=dxlnxThis is the differential equation of variable-seperable…

Q: 130 N 150 N -28m 24m SON

A:

Q: 6. What is the vector cross product 7 × F? r = 0.5i - 0.3j+ 0.9k [m] and F= -43i+54j + 61k [N]

A:

Q: b=480mm d=700mm fc'=30MPA fy=400MPA Mu=1430kN-m Determine As A. USE NSCP 2015, As = sq.mm. B. USE…

A:

Q: axis f the glebal centroid ohe section. Note: the x aN ses in the e e wsed as Re represent the d y…

A:

Dimensional homogeneity

The term dimensional homogeneity means that in an equation, the dimensions of each term on both sides are equal, which means the dimensions of the left-hand side (LHS) of an equation are similar to the dimensions of the right-hand side (RHS). For a dimensionally homogeneous equation, the powers of fundamental dimensions will be identical on both sides of the equation.