PROBLEM 2 A centrifugal pump discharges 0.15m3/s of water against ahead of 15 m. The impeller has outer and inner diameter of 35 and 15 cm, respectively The outlet vanes are set back at an angle 40 deg. The area of flow is constant from inlet to outlet and is 0.06m2. If the speed of the pump is 960 rpm. Take slip factor = 1. Calculate the manometric efficiency, and B. 57 3% C.60.7% D 39 3% A 45.9% vane angle at inlet. A 11 deg B 17 deg C.15 deg D 18 deg

PROBLEM 2 A centrifugal pump discharges 0.15m3/s of water against ahead of 15 m. The impeller has outer and inner diameter of 35 and 15 cm, respectively The outlet vanes are set back at an angle 40 deg. The area of flow is constant from inlet to outlet and is 0.06m2. If the speed of the pump is 960 rpm. Take slip factor = 1. Calculate the manometric efficiency, and B. 57 3% C.60.7% D 39 3% A 45.9% vane angle at inlet. A 11 deg B 17 deg C.15 deg D 18 deg

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Calculate the minimal head of the pump required to pump 1 m³ of water per second to the height 10 m trough a pipe with cross sectional area 0.1 m². Assume constant friction coefficient f = 0.04 and neglect all losses in fittings. The pump head is the gravity head plus losses and so it can be found?
A centrifugal pump with a 3-inches diameter impeller rotating at 1150 rpm delivered 400 gpm of water 80ºF at 250 ft total head. Find the impeller diameter of a geometrically similar pump rotating at 1750 rpm delivering 500 gpm. What is the total head of the second pump.
With a centrifugal pump directly connected to a diesel engine, 148 liters of water will be sucked 5 m deep and pumped 48 m high. The engine will be run at 1500 rpm. The total head loss in the suction pipe is 4 m.SS, the total head loss in the discharge pipe is 9 m.SS. Since the overall efficiency of the pump is 68%, find the power used by the pump. If the pump speed is reduced to 1200 RPM, what will be the flow rate and discharge head?
Need part 1 and 2
PROBLEM 5 An axial flow pump is required to deliver 1m3/s at 7m head while running at 960 rpm. Its outer diameter is 50 and hub diameter is 25 cm. Find the following: (1) flow velocity, which is assumed to be constant from hub to tip, and A. 4.59 m/s B. 6.791 m/s C. 60.7 m/s D. 39.3 m/s (2) power required to drive the pump if overall efficiency is 84%. A. 81.75 kW B. 12.03 kW C. 40.7 kW D. 60.9 kW
If a pump with a manometric head of 12 m is designed to deliver a flow rate of 7500 liters / minute. Since the rotation speed of the pump shaft is 1800 rpm, what is the dimensionless pump specific speed of this pump?
A centrifugal pump impeller has an external diameter of 1.2 m and internal diameter of 0.8 m. The width of the impeller at outlet is 0.175 m and the blade angle at outlet is 65 degrees. The flow velocities at inlet and outlet are the same (Va1 = Va2). This pump delivers 1.55 m3/s of water at 210 rpm. For theoretical performance, calculate: 1-The flow velocity . 2-blade speed at outlet. 3-blade angle at inlet (in degrees). 4-the developed head. 5-The pressure rise across the impeller. 6-The number of blades . 7-The NPSH . %3D
Q.6 Amixed flow pump is driven by a 8 kW motor running at 1000 rpm. It delivers water at the rate of 1000 liters/min against a total head of 25 m. What is the specific speed of the pump in meter-minutes? (al 90
A centrifugal pump discharges 96L/s while running at 1380rpm against a net head of 14m. The manometric efficiency of the pump is 0.92. If the vane angle at the outlet is 35 deg, estimate the outer diameter of the impeller and its width at that diameter. Assume the velocity of flow.
In a pelton wheel, calculate the power available at the inlet and the hydraulic efficiency ofthe turbine. The wheel is having semi-circular buckets, which functions under a head of 150mand consumes 0.06 m3/s of water. The 750 mm diameter wheel turns 800 rpm. Assume thecoefficient of velocity as unity.
the diameter of the suction pipe is 385mm. The diameter of the discharge pipe is 268mm. If centrifugal pump delivers 322388 L/hr of water to a pressurized tank with 293kpa. The source of water is 14m below the pump. Calculate the pump total head in meters.
A centrifugal pump delivers 80 liters per second of water on test suction guage reads 10 mm Hg vacuum and 1. 2 m below pump centerline.Power input is 70 kW. Find the total fynamic head in meters