
Mechanics of Materials (MindTap Course List)
9th Edition
ISBN: 9781337093347
Author: Barry J. Goodno, James M. Gere
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Question
thumb_up100%
This is
You must to answer it correctly using F-B-D
Don't use chatgpt
(Handwritten recommended)
![Problem #2 [0.5 mark]
The 3/4-in.-diameter bolt shown is subjected to a 6000-lb tensile load. The bolt passes through
a 3/4-in. thick plate. Compute the tensile stress in the bolt and the shear stress in the head of
the bolt.
2-in.-diameter bolt
6000 lb
Them 2.01 insiden
Hex
bolt head
Hex
bolt
head
3"
4
Bolt
shank](https://content.bartleby.com/qna-images/question/b315ba8c-cc1b-4d54-9e28-86eac3893d3f/bfd9b532-092e-403f-838d-e201b65547c3/xhjevzg_thumbnail.jpeg)
Transcribed Image Text:Problem #2 [0.5 mark]
The 3/4-in.-diameter bolt shown is subjected to a 6000-lb tensile load. The bolt passes through
a 3/4-in. thick plate. Compute the tensile stress in the bolt and the shear stress in the head of
the bolt.
2-in.-diameter bolt
6000 lb
Them 2.01 insiden
Hex
bolt head
Hex
bolt
head
3"
4
Bolt
shank
Expert Solution

This question has been solved!
Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.
Step by stepSolved in 2 steps with 1 images

Knowledge Booster
Similar questions
- 4. Solve this with a clear solution to avoid confusion.arrow_forwardPLEASE ANSWER NUMBER 1 MECH 222: PLEASE GIVE DETAILED SOLUTIONS AND CORRECT ANSWERS. I WILL REPORT TO BARTLEBY THOSE TUTORS WHO WILL GIVE INCORRECT ANSWERS.arrow_forwardPlease dont copy from other answers. Help Solving this pleasearrow_forward
- 1. A loaded bicycle pedal crank is shown below. q 750N (2 direction) 72/ A @ Top 8 yo B@ Top d = 15 mm x₁ = 125 mm x2 = 24 mm y₁ = 60 mm у2=X2 a. Sketch elements A and B and show the stress states. Clearly label the coordinate axes on the elements. Make sure you calculate the normal (o) and shear stresses (T). Do not neglect Tv. Find the principal stresses for each element using Mohr's Circle. b.arrow_forwardPlease solve 1 and 2 with neat good explainations pleasearrow_forwardProblem 2: For the shaft shown below, determine the normal and shear stresses acting on the element located at point A, including stress concentrations. Then draw the stress element at A with the applied stresses and determine the three principal stress (0₁, 02 and, 03) using Mohr's circle. r= 0.0042 m, d = 0.03 m, D = 0.033 m, T= 250 Nm P = 1500 N, M = 300 Nm, A M T J.C₁ P r M T Di darrow_forward
- 3) A 25 mm solid round shaft is supported by self-aligning bearings at A and B (the bearings do not support axial loads). Two chain sprockets are attached to the shaft as shown. a. Find the force, F, on the 125 mm diameter sprockets. b. Construct the V-M-N-T diagrams for the shaft. c. Determine the shaft location with the most severe state of stress. d. Sketch the Mohr's circle and find the principal stresses at that location. A 125 mm dia. 50-mm dia. 75 mm 25mm dia. 5000 N 150 mm 75 mmarrow_forwardThe hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.arrow_forward1-41.M A shelf is being designed to hold crates having a to- tal mass of 1840 kg. Two support rods like those shown in Figure P1-41 hold the shelf. Each rod has a diameter of 12.0 mm. Assume that the center of grav- ity of the crates is at the middle of the shelf. Compute the stress in the middle portion of the rods. 1840 kg -600 mm Support rods (2) 30% 1200 mm Shelfarrow_forward
- Compute the tensile stress for the rod shown in Fig. 1 at section A-A, the shearing stress across section B, the compressive stress between the pin and the rod, and the compressive stress between the pin and the yoke. Given n = 1 (3 / 4) in., a = (15 / 32) in., e = (27 / 32) in., b = (15 / 16) in., d = (19 / 32) in., f = 1".arrow_forward3. Calculate the bearing stress and shear stress between the pin and each bracket of a clevis joint. Assume pin diameter of 10 mm, 40 mm wide gap link, 12 mm thick bracket, and 3550N tensile load. Draw a free body diagram (geometry & forces) Identify stress plane Calculate stress and write it (with appropriate units) in the outlined boxarrow_forwardPlease give me the detailed solution. Strictly don't use chatgpt. I need a handwritten solution onlyarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning

Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning