Problem 1 The 75-pound escape hatch is held open by journal bearing A, thrust bearing B, and thin link CD. Determine the support reactions. The coordinates of each point are given below. All coordinates are in inches. A: (0, 0, 60) B: (0, 72, 60) C: (40, 50, 60) D: (50, 70,0) Center of Gravity: (30, 36, 60) Problem 1 The member shown is supported by a pin at A and cable BDC. Determine the support reactions. You may ignore the thickness of the object. Pulley D 75° 40 kip-ft 01 12 kip 15' 8'

Problem 1 The 75-pound escape hatch is held open by journal bearing A, thrust bearing B, and thin link CD. Determine the support reactions. The coordinates of each point are given below. All coordinates are in inches. A: (0, 0, 60) B: (0, 72, 60) C: (40, 50, 60) D: (50, 70,0) Center of Gravity: (30, 36, 60) Problem 1 The member shown is supported by a pin at A and cable BDC. Determine the support reactions. You may ignore the thickness of the object. Pulley D 75° 40 kip-ft 01 12 kip 15' 8'

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.8P: The figure models the handle of the water cock described in Prob. 4.9. Draw the FBD of the handle,...

See similar textbooks

Similar questions

Resultant(Using Method of members) and Equilibrium
determine the amount of reaction forces on the stage supports
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and cast is W=180 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=5 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=30°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) Answerb) Find the tensile force T2 in cable 2. (Write your result in N) Answerc) Find the angle α of cable 1 with the horizontal. Response
From the given figure shown, the cylinder has equal diameters. Solve the reaction at A. Solve the reaction at D Solve the reaction at C
Find the reaction to the car. (FBD Auto body)
The figure shows a mechanical model of the Russel fracture traction device and the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The total weight of the leg and the cast is W=200 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=10 cm . Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A ( 3L/4= 75 cm) . The angle that cable 2 makes with the horizontal is measured as β=40 ° . Accordingly, in order for the leg to remain in balance in the position shown; a) Find the tensile force T 1 in cable 1 . (Write your result in N ) b) Find the tensile force T 2 in cable 2 . (Write your result in N ) c) Find the angle α of cable 1 with the horizontal
Find the forces in the three members of the space truss shown in the figure. 600 mm 500 mm 820 mm- 550 mm 625 mm 950 N
Part A The mobile crane s symmetrically supported by two outriggers at A and two at B in order to relieve the suspension of the truck upon which it rests and to provide greater stability. The crane and truck have a center of mass at G₁ and the boom has a center of mass at G₂. The boom is supporting a load. Draw the free-body diagram for the crane and boom according to lecture instructions. Draw the vectors starting at the black dots. The location and orientation of the vectors will be graded. The length of the vectors will not be graded. 0 W crane weight of lower part of the crane W boom weight of the boom Fload force excerted by load FA reaction at A FB reaction at B 2m 1m 1m LIMI 6.25 m
The L-shaped rod AOCD has an 80 kg mass hanging from it at B. The rod is leaning against a smooth wall at A. Point B is half way up OA. There is a journal bearing at C and a thrust bearing at D. They are properly aligned. A force F is pulling in the x-direction at B. Just as the rod comes off of the wall at A, what is the magnitude of the force F. 1 m B F 1m
The telescoping arm ABC is used to provide an elevated platform for construction workers. The workers and the platform together have a mass of 212 kg and have a combined center of gravity located directly above C. Assume 0 = 20°. 5 m 2.4 m B 0.9 m 0.5 m Draw the free-body diagram of the arm ABC.
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and the cast is W=210 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=6 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=33°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) b) Find the tensile force T2 in cable 2. (Write your result in N) c) Find the angle α of cable 1 with the horizontal.
a) Determine the maximum mass of block A to maintain equilibrium. b) Calculate the corresponding tensile forces (T1, T2, T3, T4, and T5) in the five segments of the cable indicated in the figure. The centroid of Block B (base: 3a, height: 4a) is located at G. Use g=9.81 m/s². Draw all necessary diagrams and indicate the direction of the impending motion. Additional data are provided below. Hint: Check for slipping, and tipping at points L and R of block B. P = 70 N $ = 20° Parameter: WB = 84.6800 N HB = 0.2645 H12 1 A a = 40° a = 9 cm ठ H34 (3) H23 H45 0 = 50° 12 M23 34 = 0.15 a L B B = 30° μ45= 0.23 G R 22 P