Problem 1: R. +l R,(Ar) 2R R,(Ar) R,(Ax) R,(Ax) Figure 1: the sensor Figure 2: the electric circuit for measurement 1) Give the expressions of R(Ax) and Rp(Ax) as a function of Ro, L, and Ax. 2) The potentiometer is used in the electric circuit shown in figure 2. The voltage Vmes is measured by an electronic circuit which has an input impedance Rapp. Give the expression of Vmes as a function of R(Ax), Rp(Ax), R , Rupp , and Ve. 3) Assuming that Rapp >> Ro , find the equation of the transfer function of this sensor (electric circuit for measurement included). 4) Deduce the sensitivity S of this system (sensor + circuit). 5) When do we have the maximum sensitivity ?

Problem 1: R. +l R,(Ar) 2R R,(Ar) R,(Ax) R,(Ax) Figure 1: the sensor Figure 2: the electric circuit for measurement 1) Give the expressions of R(Ax) and Rp(Ax) as a function of Ro, L, and Ax. 2) The potentiometer is used in the electric circuit shown in figure 2. The voltage Vmes is measured by an electronic circuit which has an input impedance Rapp. Give the expression of Vmes as a function of R(Ax), Rp(Ax), R , Rupp , and Ve. 3) Assuming that Rapp >> Ro , find the equation of the transfer function of this sensor (electric circuit for measurement included). 4) Deduce the sensitivity S of this system (sensor + circuit). 5) When do we have the maximum sensitivity ?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

AN Sesli oku 1-In the circuit designed to measure the effective value of the sinusoidal voltage at the input, diodes are considered ideal. M deflection is a measuring element with rotating coil. Rm32k İm-(10)^-4 A. A- Draw the waveform of the current flowing through M on a scale. Determine the resistance value of R1 so that the nominal voltage value of V-m is 100V. B-What should the tolerances of the resistors be so that the Vm class is at most 1.5? (resistors have the same tolerances) ult) R2 本 R3 20k 18k R4 k: k2 10k
Q2 (a) Figure Q2(a) shows a clipper circuit made with a gemanium diode. Given the voltage input, Vin = 20 Vp-p, VDc = 5 V, Rs = 10N and RL=1 kN. (i) Sketch the full cycle of input voltage, Vin(t) in sinusoidal waveform. (ii) Determine the output voltage values for all input values. Show all the calculations and support your answers with the aid of diagram. R. Vin Si Ge R VOUT Vpc Figure Q2(a)
Q2 (a) Figure Q2(a) shows a clipper circuit made with a germanium diode. Given the voltage input, Vin = 20 Vp-p, VDc = 5 V, Rs = 10 N and R1=1 kN. (i) Sketch the full cycle of input voltage, Vin(e) in sinusoidal waveform. (ii) Determine the output voltage values for all input values. Show all the calculations and support your answers with the aid of diagram. (iii) Sketch the overall output waveform, VoUT (1).- R. + Vin Si Ge R VOUT Vpc Figure Q2(a)
1-In the circuit designed to measure the effective value of the sinusoidal voltage at the input, diodes are considered ideal. M deflection is a measuring element with rotating coil. Rm=2k İm=(10)^-4 A. A- Draw the waveform of the current flowing through M on a scale. Determine the resistance value of R1 so that the nominal voltage value of V-m is 100V. B-What should the tolerances of the resistors be so that the Vm class is at most 1.5? (resistors have the same tolerances). R1 u(t) R2 1R3 18k 20k R4 k: k2 10k
Find the equivelent resistance of the circuit below. (Rin)Conduction diodes' resistance is 0Insulating diodes' resistance is infinite.R1 = 10 ohm
If we have a voltmeter, during the measurement do we need a voltmeter with high or low input impedance to measure current. How about when we need to measure voltage drop. Please explain. ..
The input voltage in the following circuit is Vs = 33.62 V rms and the frequency is 50 Hz. The value of R;=R2= 33.62 k2. What would be the maximum voltage that the voltmeter would measure (in Volts) if the diode has a forward voltage drop of 0.9 V. Vs (+ R1 0.5uF R2 0.5uF
The diodes in the circuit depicted can be modelled as ideal diodes with an 0.7 V diode drop. The resistor values are R1 = 2.1 kO and R2 = 2.2 KQ. Vin = 120° v w = 1k rad/s Vout[max.] = Vout[min.] = R1 Ω Vout= ( What are the maximum and minimum voltage values vout takes? Also, define a and b, such that between the maximum and minimum voltages Vout= (axVin - b) V. Answer to within 1% accuracy. R2 Ω ww (₁₁ out V V Vin - ) V
Exe: The single-phase bridge rectifier has an RL Load and an ac source, with R = 10Ω andL = 10mH. The peak value of the source is Vm = 100V at 60 Hz. The expressions of voltage andcurrent outputs are:(a) Determine v0(t) and i0(t) with two ac terms (n=2 and 4)(b) Determine the power absorbed by the load.
60 V D1 D2 2 kohm DA D3 -60 V Assume that an input signal is applied to the circuit given above, as shown in the figure next to it. Accordingly, answer the following questions. The diodes used are silicon diodes, their operating voltages are 0.7 volts, and can be omitted because their resistance is very small. Calculate V p-out( Vm ) for this circuit.
In the given period,(diodes will be considered ideal.a) Draw the V0 output by calculating it according to the input.b) Calculate the average and effective value of the V0 output.c) What are the advantages and disadvantages of using two diodes and two resistors instead of four diodes?Input signal Vm = ± 10V (peak to peak), T = 2π (period),R = 7 kΩ
60 V D1 D2 2 kohm D4 D3 -60 V Assume that an input signal is applied to the circuit given above, as shown in the figure next to it. Accordingly, answer the following questions. The diodes used are silicon diodes, their operating voltages are 0.7 volts, and can be omitted because their resistance is very small. Write the name of this circuit, thinking about which circuit we do in the courses is equivalent to the purpose.