Problem 1 In the magnetic circuit shown in figure P-1 the depth of the core is 5 cm. The winding has 400 turns and the relative permeability of the core is 4000. Determine the flux produced in the core for a current in the coil of 5 A. 10cm! N 20cm Figure P-1 10cm' T 10cm * 20cm 10cm

Problem 1 In the magnetic circuit shown in figure P-1 the depth of the core is 5 cm. The winding has 400 turns and the relative permeability of the core is 4000. Determine the flux produced in the core for a current in the coil of 5 A. 10cm! N 20cm Figure P-1 10cm' T 10cm * 20cm 10cm

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Q3. What is a peak load? How does it affect the power factor and Efficiency?

A: In this question we need to discuss the following What is peak load How it affect the power factor…

Q: Find the inverse Laplace transform, f(t) of the function F(s) = = f(t) = ,t> 0 30 84, 80

Q: Vin + D₁ 不 C₁ + RL Vout The rectifier above drives a 320-02 load with a peak voltage of 3.25V. For a…

A: In this question we need to find the ripple amplitude of the given half wave rectifier.

Q: Electrical Engineering Topicwise Solved Questions A 6 pole Lap wound de generator has 300…

A: Given, Total number of pole, P = 6. Total number of conductor, Z = 300. Emf induced per conductor,…

Q: +1 12V 1 = 0 1ΚΩ 100 MH 1 μF + Fuct)

A: capacitor voltage at time t < 0 is VC ( 0) = 0 V before switch on. capacitor does not allows…

Q: What precautions can you take to ensure that your machine is protected from things like power…

A: We need to write about precautions which we take to ensure that our machine is protected from…

Q: Question 2: The circuit below is a synchronous sequential circuit based on D-type flip-flops (DFFs):…

A: The sychronous sequential circuit based on D-type flip-flop is shown below,

Q: An inductor of 5 mH has a voltage across it of 180e 12tmV. Its current at time 0 is i(0) = 10 A.…

A: Inductance L = 5 mH. Voltage is given vt=180e-12t mV. Current at at time t=0 is i0=10 A. Time t = 50…

Q: HW5: Problem 3. In the following circuits find all the node voltages and branch currents. Assume…

A: Given, beta =100 We need to calculate the all the currents Ic,IB,IE . And all the voltages Vc,VB,VE…

Q: Figure P16.3 -T -T v(t) Vm 0 v (1) Vn m 0 -V₁ v (t) m T/2 T (a) m 27 37 T (b) (c) HF 2T 3T T 3T/2

A: The Fourier series for xt is given by; xt=a0+∑n=1∞ancos nω0t+bnsin nω0t Here a0 is called as the DC…

Q: 8. Given the following constellation diagram: de jos uver une sonowing constentation unagram: 0100…

Q: 12. For the Karnaugh map shown below, write (in the box on the answer sheet) the equation…

Q: Problem # 1. 1. Find the average power (at RMS value) absorbed by the resistor and inductor. Note…

Q: The vector from the origin to the point P(3; -7; 5) is given below. So K, L, M = ? Â=Kê +Lây+ Mâ K=…

A: In this question we need to find the value of K,L &M

Q: (a) When the switch is closed, the transistor must be driven into saturation, thus applying nearly…

Q: Electrical Engineering Topicwise Solved Questions A 6 pole Lap wound de generator has 300…

A: Given- A lap wound DC generator with, Total number of poles, P = 6 Total number of parallel paths, A…

Q: The 10-cm-wide, zero-resistance slide wire shown in (Figure 1) is pushed toward the 2.5 12 resistor…

A: In this question we need to find the following Pushing force How much power does the pushing force…

Q: (8 points) What is the power factor pf for the given load ZL? You must specify leading or lagging,…

Q: The following control system is given. R is the input and C is the output. Blocks are s² represented…

A: The block diagram, Representation of the blocks, Gs=s2s3+2Hs=5

Q: Find vo for the circuit given in the figure, assuming that Ug = Vs с HH 292 = (6 cos (2t) + 4 sin…

A: In this question we need to find the voltage Vo shown in the given circuit.

Q: The message signal m(t) plotted below is a periodic function having the fundamental pe of To m(t) 7…

Q: For a balanced 3-phase system, and under the condition: Z₁ = Z₂=Z3-Zy Z2 prove that: ao bo n Z₁ =…

A: impedances are Z1 =Z2=Z3 =ZY and Za= Zb =Zc =Z∆

Q: Plot the Odd component on your answer sheet and then define the amplitudes (place the values onto…

Q: Calculate the average output voltage for a half-wave diode rectifier if the following measurements…

Q: madı rinden hiş Vx 1 A B I Ix H IR1R₁ + R₂ VB In the circuit above, plot Ix and IR1 as a function of…

A: We need to draw graph between voltage and current for given circuit.

Q: Vin D₁ K+ O + C₁7 C₁ RL Vout The rectifier above drives a 640-2 load with a peak voltage of 3.75V.…

A: In this question, We need to determine the ripple voltage. We know Ripple voltage for half wave…

Q: HW5: Problem 3. In the following circuits find all the node voltages and branch currents. Assume…

A: The above problem involves large signal analysis of NPN BJT.

Q: What are some of the most important recent advancements in electrical engineering, and how are they…

A: In the recent time there have done lot of development in the Electrical Engineering field and due…

Q: Problem 6 : (SP10.2) Note: This problem has 3 parts: a, b, and c. Remember to do all three.…

A: Given, Circuit diagram is A3A2A1A0 = 1001; B3B2B1B0 = 1100; We need to determine the output…

Q: For uncontrolled half wave rectifier, R=80ohm, L=0.15H, f=50Hz and Vm=311V. Find the point when the…

A: In this question we need to find the point when the current reaches to zero

Q: Given that the circuit shown in figure #2 resonates at the source frequency, determine: i. The value…

Q: (7) Determine Is,Ic,IE, VB,and Vc in the following figure, where Bpc is 48. ww Rc >1.2KQ Vac 14.

A: Circuit diagram is given as,

Q: The expression E(x, y, z)= xy + xyz + x +y is given 1.1 Simplify the given expression 1.2 Draw the…

A: In this question we need to simplify the given expression and draw the logic circuit of given…

Q: Obtain the equation for Y(s) from the block diagram if the Gain (K) = 4 1 X(s) 10 S+10 22 Transfer…

Q: 9. Given A = 5î - 2j-2k and B = 41+J-K, compute Proj B.

Q: Assuming an ideal op amp, design and draw the circuits for the following. Your resistor values must…

Q: Use nodal analysis to find the voltage V in the circuit given below, where vs = 145 -10 V. Please…

A: In the given questions we need to calculate the node voltage V.

Q: Differences between IEC (European) and ASIA standards for electrical safety

A: We need to differentiate between IEC (European) and ASIA standards.

Q: Problem eight. Given the following characteristic equation. Determine the range of K for a stable…

A: We need to find out range of k for stable system.

Q: A complex voltage 'v' is represented by: v=25+100 sin at +40 sin(3@t+/6) +20 sin(5@t+/12); where =…

A: Given, A complex voltage expression, v=25+100sinωt+40sin3ωt+π6+20sin5ωt+π12ω=104 rad/sR=10 ohmL=1mH…

Q: For controlled half wave rectifier, R=44ohm, f=50Hz and Vm=280V and a=0,9 rad. Calculate the rms…

Q: For uncontrolled full wave rectifier, R=44ohm, L=0.05H, f=50Hz and Vm=299V. Calculate the amplitude…

A: R is the load resistance, L is the inductance of the load, f is the frequency of the AC supply and…

Q: 2) Fill in waveforms for Q and D_OUT D P.. D_IN CLK CLK D_OUT D_IN D_OUT Ti

A: given logic diagram is

Q: For controlled half wave rectifier, R=44ohm, f=50Hz and Vm=280V and x=0,9 rad. Calculate the power…

A: In this question we need to find the power absorbed by the load

Q: Determine and sketch the magnitude response and system response of the following LCCDE system :

A: Given: A LCCDE system, y(n)=x(n)-x(n-4), To find: Magnitude response and system response of the…

Q: For the system shown generate the transfer function J1= 2 kg*m² J2= 40 kg*m² D1-10 N*m/(rad/s) D2=…

Q: A cloud of charge with a speed of 8 x 106 m/s is projected along the positive x direction into a…

A: Speed of the charge; v=8×106 m/s Flux density; B=<4,0,-3>T Charge magnitude; q=2×10-3 C To…

Q: N-point DFT, N-1 x(n) as an N-point sequence and X(k) as its Σ |x(n)|2 n=0 = 1 N-1 N Σ |X(k)|² 7c=0…

A: Given: For an N-point sequence, x(n) having, X(k)=DFT{x(n)}, Parseval's relation is,…

Q: Determine the power of R₁, R₂ and Vs1-

A: It is given that:

Q: Instructions: In the series RLC circuit shown below, the switch has been in position 'a' for a long…

A: As per the guidelines of Bartleby we suppose to answer first three subpart only for solution of…

Question

Problem 1
In the magnetic circuit shown in figure P-1 the depth of the core is 5 cm. The winding has
400 turns and the relative permeability of the core is 4000. Determine the flux produced
in the core for a current in the coil of 5 A.
10cm
N
20cm →→
Figure P-1
10cm
T
10cm
20cm
10cm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Formulae used

VIEW

Step 3: Finding flux

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

7. A coil having a resistance of 20 ohms and an inductance of 0.75 henry is connected in series with a 30-ohm resistor and to a 120-volt d-c source. A switch across the series resistor is then closed, and the circuit is assumed to be in a steady-state condition. At the instant the switch is opened, what will be the rate of current change and the power delivered by the magnetic field.
An air core toroidal coil has 120 turns, the length is 12 cm and 12 sq. cm in area What is the current required to set up a flux of 1.2x10° weber. What is the current?
A magnetic circuit has a length of 100 cm and cross-sectional area of 5 square cm. The total flux is 10 x 10 webers. The coil has 100 turns and current of 4 amperes. What is the magnetic strength? a. 500 AT/m b. 400 AT/m c. 350 AT/m d. 450 AT/m
A ferromagnetic core is shown in Figure Pl-2. The depth of the core is 5 cm. The other dimensions of the core are as shown in the figure. Find the value of the current that will produce a flux of 0.005 Wb. With this current, what is the flux density at the top of the core? What is the flux density at the right side of the core? Assume that the relative permeability of the core is 800. 1-5. 10 cm- 5em 20 em 15 cm 15 cm 15 cm Coe depth - Scm SOLUTION There are three regions in this core. The top and bottom form one region, the left side forms a second region, and the right side forms a third region. If we assume that the mean path length of the flux is in the center of each leg of the core, and if we ignore spreading at the corners of the core, then the path lengths are I, = 2(27.5 cm) = 55 cm, I, = 30 cm, and /, = 30 cm. The reluctances of these regions are:
Consider a ferromagnetic ring (nucleus) that has a mean circumference of 40 cm, 300coiled copper turns and a sectional area of 5 cm2. A current of 2 is appliedA to winding, producing a flux of 1.5 mWb.Determine the permeability of the core material.Determine the relative permeability of the core material.If the ferromagnetic ring has an air gap of 2 mm. Find the required MMFso that the flux density in the gap is 0.5 T.
A toroidal core with a mean circumference of 100 cm and a cross-sectional area of 10 cm2 is wound with 500 turns of wire. What current would be required to generate a flux of 1 mWb in the core. Assume the core has a relative permeability of 800
A magnetic ring has reluctance of 1.675 × 10⁰ AT weber. The flux to be produced by the coil is 800 x 10 webers, then the AT required for the m.m.f. will be
2. AC-core with a gap of 0.0001m has a coil number of 100 and a current of 10mA. First find the Reluctance of the core given that the Iron core has a negligible reluctance and only the air reluctance contributes to the majority of reluctance. The core has a cross sectional area of 2cm^2. Next find the flux flowing thru the C-core.
A ferromagnetic core is shown below. The depth of the core is 5 cm. The other dimensions of the core are as shown in the figure. Find the value of the current that will produce a flux of 0.003 Wb. With this current, what is the flux density at the top of the core? What is the flux density at the right side of the core? Assume that the relative permeability of the core is 1000. 1. - 10 cm--- - 20 cm - 15 cm 500 tums 15 cm 15 cm [1.21 A, 0.4 T, 1.2 T]
A coil that con sists of 450 windings is wound aroundabakelite ring. The mean diameter of the ring is 100 mm and the diameter of the bakelite core is 20 mm. The currentthrough the coil is 3 A. Determine: 1.1 a) the field stren gth b) the flux den sity c) the total flux A ringhas two halves. The onehalf is made from Cast iron, while the other is made from Cast steel. The two halves are held 1 mm apart with the aid of a paper disc. The cross-section al area and mean circumference of the ringis 345 mm? and0.6 m respectively. Therelative permeability of cast iron is 2400, while that of cast steel is 600. The ring has a coil with 200 win dings. The currentflow through the coil causes a flux den sity of 0.48T. 1.2 Calculate the: a) mmi b) currentflow Ignore the effects of fringing andleakage.
10. A potential difference of 250 V is applied to a field winding at 15-C and the current is 5 A. What will be the temperature of the winding when current has fallen to 3.91 A applied voltage being constant. Assume temperature coefficient at 15'C is equal to 1/254.5 per °C
5. A toroidal core with a mean circumference of 100 cm and a cross-sectional area of 10 cm2 is wound with 500 turns of wire. What current would be required to generate a flux of 1 mWb in the core. Assume the core has a relative permeability of 800 а. 1.0 А c. 1.5 A b. 2.0 A d. 2.5 A