Problem 1: Find vi and in by combining resistors in series and parallel (i.e. finding Reg). 1k2 5k2 V1 10k2 2k2 10kΩ 10kΩ 1mA 5k2

Q: ?Which of the following protects only against over-current (äbäi 2) MCB ELCB O RCCB C Socket C

A: Given, Which of the following protects only against over current

Q: Q2) In the load test, is the iron loss present?

A:

Q: for the Chavacterstic fad ealuation shown Value of below for the the RH Which Yemain stable using…

A: for the characteristic equation shown above find the value of k for which the system remain stable…

Q: What is the smallest square box that will accommodate four No. 12 conductors and four No. 10…

A: conductor A conductor is any piece of material that easily allows heat or electricity to pass…

Q: How many conductors should be in the jaws of the meter when measuring current? a. One conductor of…

A:

Q: Explain thevenin equivalent circuit for dummies?

A: ELECTRICAL NETWORK: When addressing a circuit problem or constructing a balanced circuit, the word…

Q: Three phase gas pressure cable (Draw, Identify and Mark all the parts)

A:

Q: Gi G3 土 G2 Gu

A:

Q: 70. A circuit supplies a continuous load of 38 amperes and is protected by a 50-amperecircuit…

A: While calculating the conductor size for a continuous load, take 125% of overloading conditions…

Q: What is earth voltage?

A: What is earth voltage.

Q: Draw the connection diagram for  a low voltage wye

A: Draw the connection diagram for a low voltage wye?

Q: Page (We 81 14 &0.7& w = 4radisec aith then Valve op kg ai ? ay K = 9 7 U4=0.25 66 K+/60120022 2 &…

A: It is given that:

Q: Auxillary carry flag will be set whenever а. there is a carry from lower nibble to higher nibble as…

A: Choose the correct option Auxiliary carry flag will be set if?  8085 microprocessor is 8 bit…

Q: im looking for the k-maps for TA and TB

A:

Q: Discuss  and compare the various method of neutral earthing

A: Different earthing methods are given below, 1. Underground neutral earthing : In ungrounded earthing…

Q: Direction: List one (1)  safety precaution on electrical apparatus and one (1) safety precaution on…

A:

Q: A 24A, 240V single-phase load having a length of 100 ft is located 100 ft from a panel board and is…

A: A 24A, 240V single-phase load having a length of 100 ft is located 100 ft from a panel board and is…

Q: Refer to the National Electrical Code or the working drawings when necessary. Where applicable,…

A: We are authorized to answer one question at a time, since you have not mentioned question you are…

Q: Count Mounting method 15. From the information you have studied about the various electrical…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: A 4" conduit installed with 4 # 750 kcmilTHWN-2, and 1 #1 THWN conductors. The conduit due to…

A: It is given that: Pull boxes are utilized in straight pull configuration so that the conduits enter…

Q: For the following circuit find VL, IL, Iz and IR if RL = 180 , repeat for R₁ = 470 R$ 20 V 220 2 Vz=…

A: Given: Circuit diagram,

Q: 2- Which quantity has been measured in order to measuring B?

A: we need to find Which quantity has been measured in order to measuring B.

Q: For the circuit in Figure 1, using a VREF of 10V what could be the highest possible output voltage…

A:

Q: For measurement instrument, the crucial -1 static characteristic is resolution аccuracy sensitivity

A: Since there are multiple questions uploaded within the same question, therefore solving the first…

Q: A distributor arranged to form a closed loop

A: A distributor arranged to form a closed loop and fed at one or more points is ring distributor ,…

Q: Type of earthing and explain each of them

A: Given: Type of earthing and explain each of them.

Q: Solve and click the answer of your choce. For the given questions, refer to FIGURE 1.0 Voltage drop…

A: Use voltage division rule

Q: What is a closed path made of several branches of the network called? Select the correct response:…

A: Select the correct option : The closed path made of several branches of the network called :…

Q: Problem 1 is a review of your understanding of KVL (Kirchhoff's voltage law) Using KVL find the…

A: A simple question based on network analysis and the topics described in the solution are kirchoff's…

Q: Define the term tariff

A: According to the question we have to discuss tariff.

Q: 5. In a three-phase circuit, if a fuse is lost and voltage is lost in phase 1, what must be true…

A: 5. In a three-phase circuit, if a fuse is lost and voltage is lost in phase 1, what must be true…

Q: 2) in to ss aloin 3 Times experiment, f event A = Head apper r only} 13- { simillar out Comes} c- {…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: In general, the letter-type designation R formerly referred to a -based covering and now indicates…

A:

Q: Vdc0 U=12 V Circuit #1 Ried LED www Ried_series Vdc0 U= 12 V Current in LED (A) Circuit 0.03 #₂ 0.02…

A: Given Data:An LED illumination circuit with,Supply voltage Set-current of the diodes V-I…

Q: elements in a circuit that carry the same current are said to be ______ a. closed-loop b. network…

A: We need to fill the blank space .

Q: Electrical Circuits (a) the relationship between line and phase voltages of a 4-wire STAR resistive…

A: In this question we need to find the following the relationship between line and phase voltages of…

Q: 1. The letter designation SL on an electrical draw- ing indicates a a. limit switch b. low-voltage…

A: As per our policy, i am attempting first question. The letter designation SL on an electrical…

Q: What is EMMI?

A: EMMI tends for ELECTRICAL MEASUREMENT AND MEASURING INSTRUMENTS.

Q: x Mol Technician/Electrician Cand X Exam - c…

A: An electric cable is a wire which carries charge or current from on point to another.

Q: Which of the following is considered a pushing force? A) Resistance B) Voltage C) Current D) All of…

A: Pushing force: The force which pushes electron through circuit resulting in electrical current flow…

Q: each other that supply the critical and the normal feeder circuits. These two panelboards must be…

A: 12a) fact based question because these are standards set by NEC  Correct option is AWG4  AWG stand…